Sanyo PLC-XF1000 Service Manual

Also see for PLC-XF1000: Brochure & specs Owner's manual Technical information Owner's manual Manual

Contents

AKE8-XF100000Parts description and reading in schematic diagram1. The parts specification of resistors, capacitors andcoils are expressed in designated code. Please checkthe parts description by the following code table.. Some of transistors and diodes are indicated in markfor the substitution of parts name. Please check theparts name by the following code table.3. Voltages and waveforms were taken with a videocolor bar signal (1Vp-p at 75 ohms terminated) andcontrols to normal.4. Voltages were taken with a high-impedance digitalvoltmeter.Example L C1 4R7 K NToleranceInductance valueManufacture codeUnique codecoil readingNote: Resistor which is indicated with resistance value only are1/6W carbon resistor. Resistor which is indicated withmaterial, tolerance and value are 1/4W rated wattage.● tolerance table● Material table● Material table ● tolerance table● diode● transistor(1) NPN typediode/transistor type reading() PNP type(3) Chip typeExample 000 K K 1000 BGExample 160 E M 10Capacitance valueExcepting electric capacitors, allcapacitance values of less than 1are expressed in μF and more than 1are in pF.capacitor readingCharacteristicToleranceTypeRated voltageMark MaterialE ElectrolyticP Electrolytic (non-polarized)C Ceramic (temperature compensation)K CeramicF PolyesterN PolypropyleneM Metalized polypropyleneH Metalized polypromylarB Ceramic (semiconductor)G Metalized polyestelY Composite filmS StyrolT Tantalum oxide solid electrolyticU Organic semiconductive electrolyteD Electric double layer electrolyticMark ToleranceA not specifiedB ±0.1C ±0.25D ±0.5F ±1G ±2E ±2.5H ±3J ±5K ±10M ±20N ±30P +100 -0Q +30 -10T +50 -10U +75 -10V +20 -10W +100 -10X +40 -20Y +150 -10Z +80 -20Mark Tolerance (nH) Mark Tolerance (%)C ±0.25 G ±2D ±0.5 J ±5S ±0.3 K ±10A ±0.2 L ±15M ±20Mark MaterialD CarbonN Metal filmS Oxide metal filmC SolidG Metal glazeW Wire wounding or cementH CeramicF FusibleMark ToleranceA ±0.05B ±0.1C ±0.25D ±0.5F ±1G ±2J ±5K ±10M ±20P +5 -15Z used in 0 ohmMark Type numberR 1S2076A,1S2473,1N4148AA 1S2076A,1S2473,1SS133,1N4148Mark Type number-- 2SC536 2SC945A 2SC1815 2SC1740SAD NF, NG PA, QA Y, GR Q, R, SAE NF, NG PA, QA, RA O, Y, GR Q, R, SMark Type number-- 2SA608 2SA564A 2SA1015 2SA933SAB NF R Y, GR RAC NF Q, R O, Y, GR Q, RMark Type number-- 2SA1179N 2SA1037K 2SA1037AK 2SC2812/N 2SC2412KAJ M6, M7 R, S R, SAH L6, L7 R, SExample 1/ D J 10K BExample 6 W K 8.Example 1/ C K 1Mresistor readingCharacteristicZ (Carbon fuse)B (Non-burnable)Resistance valueTolerance (see below table)Material (see below table)Rated wattage (W)K indicates in KWM indicate in MW