Sanyo PLC-XF1000 Service Manual

Also see for PLC-XF1000: Brochure & specs Owner's manual Technical information Owner's manual Manual

Contents

-69-Electrical Adjustment10. Gamma shipment adjustmentSoftware PROJECTOR SERVICE TOOL v4.0Use the software to obtain the proper gray scale. See thefurther information of the software instruction manual.13. Wind Sensor calibration1. Enter the service mode.. Select group no. “170” and item no. “4”. Confirm theData value is “1”.0: Wind sensor function Disable1: Wind sensor function Enable3. Select group no. “170” and item no. “0”.4. To start the adjustment, change data value from “0”to “1”. After the auto-calibration completed, "OK" willappear on the screen.IMPORTANTBefore taking this adjustment, you need to replace the airfilter with new one or scroll up the filter sheet and makesure the cabinet top, filter cover and filter cartridge aresecurely installed.11. Color Shading Correction adjustmentSoftware PROJECTOR SERVICE TOOL v4.0Use the software to correct the color shading of thescreen. See the further information of the software in-struction manual.The color shading correction adjustment for this modelshould be performed with the whole-gray patterns speci-fied as below.8-input patterns:5% gray, 10% gray, 15% gray, 20% gray,30% gray, 50% gray, 60% gray, 80% gray9. Common center adjustmentInput mode Computer modeInput signal 50% (R,G,B) pattern signal1. Enter the service mode.. Project only one color component to the screen.Select Group "900", No. "1" and then change data val-ue from "2" to "0".3. Change data value to obtain the minimum flicker foreach color on screen.Group No. Screen280 - 9 only green color picture280 - 10 only blue color picture280 - 11 only red color picture4. Select Group "900", No. "1" and then change datavalue from "0" to "2".12. White balance adjustment1. Enter the service mode. (Input signal is not required.). Select Group and No. of white balance adjustmentitems referring to the table below. For example, whenadjusting the white balance in the Standard PC modewith Advanced color : Auto, select Group - No. "98- 1 (X value)" or "98 - (Y value)".3. Change the Data value.4. Select Group "982", No. "64". When the data valueis changed "0" to "10", the adjustment is performedautomatically. The displayed adjustment Group -No.changes to "930 - 0" and it takes for -3 minutes tocomplete the adjustment.5. Check proper white balance and gray scale are ob-tained in the selected input mode.i This white balance adjustment can be done in eachlamp mode of " lamps", "Lamp 1" and "Lamp ".Group-No. Advanced color mode:Input Adjustment Mode (X, Y) data (Initial value)982 - 1 Advanced color-Auto: PC Standard -X 310982 - 2 Advanced color-Auto: PC Standard -Y 330982 - 9 Advanced color-Auto: PC Real -X 315982 - 10 Advanced color-Auto: PC Real -Y 340982 - 17 Advanced color-Auto: AV Standard -X 310982 - 18 Advanced color-Auto: AV Standard -Y 330982 - 25 Advanced color-Auto: AV Cinema -X 315982 - 26 Advanced color-Auto: AV Cinema -Y 328982 - 33 Advanced color-Off: PC Standard -X 287982 - 34 Advanced color-Off: PC Standard -Y 317982 - 41 Advanced color-Off: PC Real -X 292982 - 42 Advanced color-Off: PC Real -Y 323982 - 49 Advanced color-Off: AV Standard -X 287982 - 50 Advanced color-Off: AV Standard -Y 317982 - 57 Advanced color-Off: AV Cinema -X 313982 - 58 Advanced color-Off: AV Cinema -Y 329