-48-Read description in the Capacitor and Resister as follows: Marked ( Revised Aug. / 2000 )CAPACITOR ( Revised May / 1998 )CERAMIC 100P K 50V Rated VoltageRated value: P=Pico farad, U=Micro faradFIXED RESISTERCARBON 4.7K J A 1/4W Rated WattageRated value, ohms : K: X1,000 ohms. M: X1,000,000 ohmsA< Electrical Parts List> Note: Part order must contain Chassis No., Part No., and descriptions.Product safety should be considered when a component replacement is made in any area of a Projector. Components indicated by a mark in this parts list andthe schematic diagram show components whose value have special significance to product safety. It is particularly recommended that only parts specified on the follow-ing parts list be used for components replacement pointed out by the mark.Material :CERAMIC Temperature compensating ceramicHigh dielectric rate ceramicSemiconductor ceramicMT-PAPER Metallized paperPOLYESTER PolyesterMT-POLYEST Metallized polyesterPOLYPRO PolypropyleneMT-POLYPRO Metallized polypropyleneCOMPO FILM Composite filmMT-COMPO Metallized composite filmSTYRENE StyrolTA-SOLID Tantalum oxide solid electrolyticAL-SOLID Aluminum solid electrolyticELECT Aluminum foil electrolyticNP-ELECT Non-polarized electrolyticOS-SOLID Aluminum solid capacitors withorganic semiconductive electrolytePOS-SOLID Polymerized organic semiconductorDL-ELECT Electric double layer electrolyticAL-SOLID Aluminum manganese wind solidPPS-FILM Polyphenylene sulfide filmMT-PPS-FILM Metallized Polyphenylene sulfide filmMT-PEN-FILM Metallized polyethylenenaphthalate filmEP-ELECT Electric Conductor Polymerized Aluminum foil electrolyticCAPACITOR OtherTolerance SymbolsStatic capacitance of 10PF or lessA: Non-designatedB: ±0.1PFC: ±0.25PFD: ±0.5PFF: ±1PFG: ±2PFH: +0.1 ~ -0PFL: +0 ~ -0.1PFR: +0.25 ~ -0PFS: +0 ~ -0.25PFE: +0 ~ -1PFJ: ±5%K: ±10%M: ±20%Note: J. K. and M are used only fortubular Ceramic CapacitorsStatic capacitance of more than 10PFA: Non-designatedB: ±0.1%C: ±0.25%D: ±0.5%F: ±1%G: ±2%E: ±2.5%H: ±3%J : ±5%K: ±10%L : ±15%M: ±20%N: ±30%P: +100 ~ -0%Q: +30 ~ -10%R: +20 ~ -0%T: +50 ~ -10%U: +75 ~ -10%V: +20 ~ -10%W: +100 ~ -10%X: +40 ~ -20%Y: +150 ~ -10%Z: +80 ~ -20%Performance Symbols:A: GeneralB: Flame retardance (including noncombustible)Z: Low noise ( Less than 100Kohms : 0.3uV/V,100Kohms to 1Mohm : 0.5uV/V,More than 1Mohm : 1.0uV/V )C~Y : Temperature characteristicsT: ±10ppm/˚CU: ±25ppm/˚CC: ±50ppm/˚CD: ±100ppm/˚CE: ±200ppm/˚CF: ±250ppm/˚CG: ±350ppm/˚CH: ±1000ppm/˚C±10%W: ±1200ppm/˚C±10%Y: ±1400ppm/˚C±10%J: ±2000ppm/˚C±10%K: ±2400ppm/˚C±10%L: ±2700ppm/˚C±10%M: ±3000ppm/˚C±10%N: ±3300ppm/˚C±10%P: ±3600ppm/˚C±10%Q: ±3900ppm/˚C±10%R: ±4200ppm/˚C±10%S: ±4300ppm/˚C±10%V: ±4500ppm/˚C±10%X: ±800ppm/˚C±150ppm/˚CO: +500ppm/˚C ~ -250ppm/˚CTolerance Symbols:A: ±0.05%B: ±0.1%C: ±0.25%D: ±0.5%F: ±1%G: ±2%J: ±5%K: ±10%M: ±20%P: +5 ~-15%Z: Use when 0 ohmMaterial :CARBON Carbon film fixedMT-FILM Metal film fixedOXIDE-MT Metal oxide film fixedSOLID SolidMT-GLAZE Metal glaze type fixedWIRE WOUND power type covered wiring fixedCERAMIC RES Ceramic fixedFUSIBLE RES FusibleRESISTER Used for "others" Note) ;1. "General" (symbol A) means properties for which there are some differences among manu-facturers but which can be used when within the range given in the catalogs.2. Parts for which temperature characteristics are especially designated (required) due todesign are indicated by "temperature characteristic classifications" (symbol C to Y).Othersare indicated by "General" (symbol A).3. What are called "cement resistors" are noncombustible,so are indicated as "General"(sym-bol A),not "Flame retardant (including noncombustible)"(symbol B)AA