Tascam DR-100 MKIII Owner's Manual

Also see for DR-100 MKIII: Guide to using Comparison chart Owner's manual Owner's manual Service manual

Contents

Tascam DR-100 MKIII Owner's Manual Manual pdf 15 page image

TASCAM DR-100MKIII 15Message listThe following is a list of the pop-up messages.Refer to this list if one of these pop-up messages appears on the DR-100MKIIIand you want to check the meaning or determine a proper response.Message Meaning and responseALL HOLD on The input level knob and all buttons have beendisabled by the HOLD switch.LEVEL HOLD on The input level knob has been disabled by theHOLD switch.Battery empty Recharge the built-in battery or replace theremovable batteries.Battery lowNo card Load an SD card.Card protectedMove the write-protection switch to the unlockedposition in order to record or erase data on the SDcard.Card error The SD card was not recognized.Change the SD card.Card full The SD card has no remaining space.Format errorFormat cardThe SD card is not formatted properly or the card isbroken.Press the ENTER/MARK button to start formatting.Formatting will erase all the data on the SD card.Invalid cardChange cardSomething might be wrong with the SD card.Change the SD card.MBR errorInit cardThe SD card is not formatted properly or the card isbroken.Press the ENTER/MARK button to start formatting.Formatting will erase all the data on the SD card. Ifformatting is not possible, change the SD card.Write errorREC continueWriting to the SD card timed out. This has causedaudio to be interrupted and noise to occur.A BOF mark is added at the point when audio wasinterrupted.Card slowCheck BOF MARKSD card writing performance has become worse.A BOF mark has been added at the point whenaudio was interrupted because writing to the SDcard timed out.Check the audio around the BOF mark.Execute the erase format function or change the SDcard.Invalid sys fileMake sys fileThe system file required to operate this unit isinvalid.Press the ENTER/MARK button to create a systemfile.No sys fileMake sys fileThe system file is missing. This unit requires a systemfile for operation.Press the ENTER/MARK button to create a systemfile.Message Meaning and responseNon-supported Please see the Reference Manual for file formatsthat this unit can use.File full Recording is not possible because the total numberof folders and files would exceed the limit of 5000.File not found A file cannot be found or a file might be damaged.Please check that file.Can't deleteFile protectedRemove protection from a file before trying todelete it.Can't divideFile too short The file is too short, so it cannot be divided.Can't divideCurrent file MP3 MP3 files cannot be divided.Can't divideDup file nameThe divide function would cause the file name tobe the same as that of an existing file in the samefolder.Use a computer to change the file name.Can't divideNo markFiles that do not have marks cannot be divided withthis function.Can't divideShort intervalMark division will not work when the intervalbetween marks is two seconds or less.Can't divideNo file There is no audio file.Can't divideFile name errDivision is not possible because the file namewould exceed the limit of 200 characters.Use a computer to change the file name.MARK full The number of marks has reached the limit of 99.Can't deleteNot emptyYou cannot delete a folder that contains files.Delete all the files in the folder and try again.No XRI dataNo XRI data has been saved in the file. Turn theXRI data recording function ON before startingrecording.XRI data cannot be saved when recording MP3 files.Can't MARKFile protectedMarks cannot be added because the file isprotected from writing.Remove protection from a file if you want to addmarks to it.Can't MARKFile length Marks cannot be added because the file is too short.Digital-InUnlockNothing is connected to the digital input (DIGITALIN) connector or the signal is not being inputcorrectly.Check the digital connection.Digital-InLock Digital input has been properly detected.DIN sampleUnmatchThe digital input sampling frequency does notmatch the recording setting.I/O too short The IN and OUT points are too close together. Setthem with at least 1 second between them.Message Meaning and responseThermal AlertConnect USB PWRThe internal temperature has risen while using thebuilt-in battery and/or AA batteries.Continued use is possible by supplying power witha USB connection.Thermal Alert The internal temperature has risen.The system will shut down automatically.If any other error occurs, turn the unit off and restart it.