VADDIO ONELINK Installation And User Manual
Also see for OneLINK: Installation and user guide
                    | |
Contents
| 
OneLINK For RoboSHOT HDMI CamerasOneLINK For RoboSHOT HDMI Cameras Page 15 of 20G ENERAL S PECIFICATIONSNotes: Specifications and pricing are subject to change without prior notice or obligation.For dimensional drawings of the products, go to support.vaddio.com and click on drawings.APPENDIX 1: CONNECTORS AND SIGNALSOneLINK HDMI EZIM - RS-232 Control Port RJ-45PIN# Signal1) Unused2) Unused3) Unused4) IR GND5) IR (non-mod)6) GND7) TX (to RX of camera)8) RX (from TX of camera)OneLINK HDMI Interface - OneLINK HDMI Interface - RS-232 Control Port (RJ-45)PIN# Signal1) Unused2) Unused3) Unused4) Unused5) Unused6) GND7) RX (from TX of controller)8) TX (to RX of controller)OneLINK HDMI Interface - Ethernet Network Port (RJ-45)PIN# Signal1) TX+_D12) TX-_D13) RX+_D24) BI+_D35) BI-_D36) RX-_D27) BI+_D48) BI-_D4OneLINK HDMI Interface - IR output on Euro style 3-pin:PIN# Signal1) Modulated IR2) Common Ground3) Non-modulated IROneLINK System for Vaddio HDMI CamerasPart Numbers 999-9590-000: OneLINK System for Vaddio RoboSHOT HDMI Cameras (North America)999-9590-001: OneLINK System for Vaddio RoboSHOT HDMI Cameras (International)Included Cables (camera side)One (1) 12” (305mm) HDMI Male to Male camera cableTwo (2) 12” (305mm) Cat-5e Patch Cables (Ethernet and RS-232)One (1) 12” (305mm) power cableVideo Support HDMI resolutions up to 1080p/60 for the RoboSHOT HDMI cameras. The OneLINKarchitecture will support up to 2160p/30…for the future.RS-232 Support Pass-throughEthernet Support Pass-throughCamera Power Support 12 VDC, 3 Amp at EZIMCabling Distances Up to 328’ (100m) over Cat-5e/6OneLINK Interface Power Supply 48 VDC, 1.36 AmpConnectors on OneLINK InterfaceOneLINK Port on Shielded RJ-45F, HDMI Output Receptacle, Ethernet on shielded RJ-45Fwith LEDs, RS-232 on shielded RJ-45 connector, Power in on 5.5mm OD x 2.5mm ID Coaxialconnector (positive Center), IR Forward on 3-pin Phoenix-style connectorConnectors on OneLINK EZIM OneLINK Port on Shielded RJ-45F, HDMI Input Receptacle, Ethernet on shielded RJ-45Fwith LEDs, RS-232 on shielded RJ-45 connector, Power out on EIAJ-04 connectorOneLINK Interface Dimensions(H x W x D - not including Space-time)1.72” (43.7mm) H x 8.375” (212.7mm) W x 6.00” (152.4mm) DOneLINK EZIM Dimensions (H x W x D) 3.861” (98.07mm) H x 4.310” (109.47mm) W x 1.24” (31.5mm) DOneLINK Interface Weight 1.553 lbs. (703.1g)OneLINK EZIM Weight: 0.553 lbs. (249.5g)Operating Temperature/Humidity 0°C (32°F) to 40°C (104°F), 20% to 80% Relative HumidityStorage Temperature -20°C (-4°F) to +60°C (140°F)1234567812345678123456781 2 3Not Used with the RoboSHOTHDMI Cameras |
Related manuals for VADDIO OneLINK
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine