Quick setup guidePressure transmitter with ceramicmeasuring cellVEGABAR 82Slave sensor for electronic differential pres-sureWith SIL qualificationDocument ID: 48051

quick setup guide

For your safety

EU conformity

Product description

Mounting

Connecting to power supply

Single chamber housing

Connection example

Set up with the display and adjustment module

Parameter adjustment

Menu overview

Supplement

Information

Vega VEGABAR 82 Quick Setup Manual

product information

measuring principle

Type overview

measured variables

Selection criteria

Housing overview

voltage supply

Electronics - 4 ... 20 mA/HART - two-wire

Electronics - Proﬁbus PA

Electronics - Foundation Fieldbus

Electronics - Slave sensor for electronic diﬀerential pressure

Operation

Dimensions

VEGABAR 82

operating instructions

About this document

Environmental instructions

Principle of operation

Supplementary cleaning procedures

Accessories and replacement parts

Ventilation and pressure compensation

Combination Master - Slave

Level measurement

Differential pressure measurement

Interface measurement

Density measurement

Density-compensated level measurement

External housing

power supply

Functional safety (SIL)

Safety concept of the parameterization

Diagnosis, asset management and service

Rectify faults

Exchange process module on version IP 68 (25 bar)

How to proceed if a repair is necessary

Dismount

ambient conditions

Calculation of the total deviation

Practical example

Industrial property rights

Authorised personnel

Permissible process pressure

Product description 2.1 Configuration

Mounting 3.1 General instructions for use of the instrument

Connecting to power supply 4.1 Connecting

Set up with the display and adjustment module 5.1 Parameter adjustment - Quick setup

Parameter adjustment - Extended adjustment

Supplement 6.1 Technical data

about this document

appropriate use

permissible process pressure

environmental instructions

product description

principle of operation

accessories and replacement parts

general instructions

ventilation and pressure compensation

process pressure measurement

level measurement

external housing

Connecting to power supply 5.1 Preparing the connection

Connecting

single chamber housing

Housing IP 66/IP 68 (1 bar)

External housing with version IP 68 (25 bar)

Switch-on phase

Set up with the display and adjustment module 6.1 Insert display and adjustment module

adjustment system

Measured value indication

Parameter adjustment - Quick setup

Saving the parameterisation data

parameter adjustment

Maintenance

Diagnosis function

rectify faults

Exchange process assembly with version IP 68 (25 bar)

exchanging the electronics module

dismounting steps

technical data

Calculation of the total deviation - Practical example

symbols used

for your safety

Mounting 4.1 General instructions

connection example

Set up with the display and adjustment module 6.1 Parameter adjustment - Quick setup

Diagnosis, asset management and service 7.1 Maintenance

Dismounting steps

Function

For your safety 2.1 Authorised personnel

Configuration

Packaging, transport and storage

Process pressure measurement

Connecting to power supply 5.1 Connection of the battery charger

Adjustment system

Setup with PACTware 7.1 Connect the PC

Set up with other systems 8.1 DD adjustment programs

Diagnosis, asset management and service 9.1 Maintenance

Diagnosis memory

Exchanging the electronics module

Technical data

namur recommendations

Mounting 4.1 General instructions to use the instrument

Saving the parameter adjustment data

Diagnosis, asset management and service 8.1 Maintenance

Calculation of total deviation (according to DIN 16086)

software update

SIL features

Double chamber housing Ex d

Double chamber housing Ex d ia

Double chamber housing with DIS-ADAPT

Functional safety (SIL 6.1 Objective

Set up with the display and adjustment module 7.1 Insert display and adjustment module

Setup with PACTware 8.1 Connect the PC

Set up with other systems 9.1 DD adjustment programs

Diagnosis, asset management and service 10.1 Maintenance

Asset Management function

output signal

how to proceed if a repair is needed

Measuring range - permissible process pressure

Connecting to power supply 4.1 Connection of the battery charger

Set up with the display and adjustment module 5.1 Insert display and adjustment module

SIL qualification according to IEC 61508

Double chamber housing

general safety instructions

Connecting to the bus system

Double chamber housing with VEGADIS-Adapter

instrument settings

Setup with PACTware

Set up with other systems

Software update

Supplementary information Foundation Fieldbus

Connecting to power supply and bus system

Wiring plan

Set up the sensor with the display and adjustment module

Setting up sensor and Modbus interface with PACTware

Set instrument address

Basics Modbus

Modbus register

Modbus RTU commands

Levelmaster commands

Configuration of typical Modbus hosts

Product description 3.1 Configuration

Mounting 4.1 General instructions for use of the instrument

Set up with the display and adjustment module 7.1 Parameter adjustment

How to proceed if a repair is needed

Dismount 9.1 Dismounting steps

Connecting to power supply and bus system 4.1 Connection

Set up the sensor with the display and adjustment module 5.1 Insert display and adjustment module

Ex-d-ia double chamber housing

Diagnostics and servicing


Contents quick setup guide Table Of Contents For your safety EU conformity Product description Mounting Connecting to power supply Single chamber housing Connection example Set up with the display and adjustment module Parameter adjustment Menu overview Supplement Information	Quick setup guidePressure transmitter with ceramicmeasuring cellVEGABAR 82Slave sensor for electronic differential pres-sureWith SIL qualificationDocument ID: 48051 Next / 20