WAGNER FLEXIO 2500 Owner's Manual

TROUBLESHOOTING8MAINTENANCE • ENTRETIEN • MANTENIMIENTOREPLACING THE FILTERAttentionBefore every use, you should inspectthe air filter in the turbine to see if it isexcessively dirty. If it is dirty, follow thesesteps to replace it.Never operate your unit without theair filters. Dirt could be sucked in andinterfere with the function of the unit.1. Press the tab at the rear of the turbine. Slide the rearhousing off of the back of the turbine.2. Remove the dirty filter from the turbine and replacewith a new one. The smooth side of the air filter mustbe placed toward the turbine.Secure the cover back onto the turbine.REMPLACEMENT DU FILTREAttentionVous devriez inspecter les filtre à air quiest situé dans la turbine pour vérifiers’il est excessivement encrassé. S’il estencrassé, veuillez suivre les étapes ci-dessous pour le remplacer.Ne jamais faire fonctionner votreappareil sans le filtre à air. Des impuretéspourraient être aspirées et causer desinter-férences dans le fonctionnement del’appareil.1. Appuyez sur l’onglet à l’arrière de la turbine. Retirez leboîtier arrière en le glissant de la turbine.2. Enlevez le filtre souillés de la turbine et remplacez-lespar de nouveaux. Le côté lisse du filtre à air doit êtreplacé vers la turbine.Remettez le couvercle sur la turbine.REEMPLAZO DEL FILTROAtenciónEs conveniente que inspeccione el filtrode aire de la turbina para controlar siestá excesivamente sucio. Si se encuentrasucio, siga los pasos a continuación parareemplazarlo.Nunca haga funcionar la unidad sinle filtro de aire. La suciedad puedeingresar en la unidad e interferir con sufuncionamiento.1. Presione la lengüeta en la parte posterior de laturbina. Deslice la carcasa posterior y sáquela de laparte posterior de la turbina.2. Retire le filtro sucios de la turbina y reemplácelos pornuevo. Se debe colocar el lado suave del filtro de airehacia la turbina.Fije le tapa de vuelta en la turbina.PROBLEM CAUSE SOLUTIONProblem A: Little or no material flow 1. Nozzle clogged.2. Suction tube clogged.3. Material flow setting too low.4. Suction tube loose.5. No pressure build up in container.6. Air filter clogged.7. Spray material too thick.8. Nozzle seal missing or worn.1. Clean.2. Clean.3. Increase material flow setting.4. Remove and replace as tightly as possible.5. Tighten container. Check the air vent hole on the pickup tube - clean if clogged.6. Change7. Thin.8. Replace nozzle.Problem B: Material leaking 1. Nozzle loose.2. Nozzle worn.3. Nozzle seal missing or worn.4. Material build-up on air cap and nozzle1. Tighten.2. Replace.3. Replace nozzle.4. Clean.Problem C: Spray pattern too thick, runs and sags 1. Material flow setting too high.2. Air power setting too low.3. Applying too much material.4. Nozzle clogged.5. Air filter clogged.6. Too little pressure build-up in container.7. Spray material too thick.1. Decrease material flow setting.2. Increase air power setting.3. Adjust material flow or increase movement of spraygun.4. Clean.5. Change.6. Tighten container.7. Thin.Problem D: Spray jet pulsates 1. Material in container running out.2. Air filter clogged. 1. Refill.2. Change.Problem E: Too much overspray 1. Gun too far from spray object. 1. Reduce distance (6”-8” is ideal).Problem F: Pattern is very light and splotchy 1. Moving the spray gun too fast.2. Material flow setting too low.3. Air power setting too high.1. Adjust material flow or decrease movement of spraygun.2. Increase material flow setting.3. Decrease air power setting.