WAGNER FLEXiO 4000 Owner's Manual

Also see for FLEXiO 4000: Owner's manual

8MAINTENANCE • ENTRETIEN • MANTENIMIENTOREPLACING THE FILTERAttentionBefore every use, you should inspectthe air filters in the turbine to see if it isexcessively dirty. If it is dirty, follow thesesteps to replace it.Never operate your unit without theair filters. Dirt could be sucked in andinterfere with the function of the unit.1. Press the tabs on each side of the turbine to removethe filter covers.Remove the dirty filters from the turbine and replacewith new ones. The smooth side of the air filter mustbe placed toward the turbine.Secure the covers back onto the turbine.REMPLACEMENT DU FILTREAttentionVous devriez inspecter les filtres à airqui est situé dans la turbine pour vérifiers’il est excessivement encrassé. S’il estencrassé, veuillez suivre les étapes ci-dessous pour le remplacer.Ne jamais faire fonctionner votreappareil sans le filtre à air. Des impuretéspourraient être aspirées et causer desinter-férences dans le fonctionnement del’appareil.1. Enfoncez les languettes de chaque côté de la turbinepour enlever les couvercles de filtre.Enlevez les filtres souillés de la turbine et remplacez-les par de nouveaux. Le côté lisse du filtre à air doitêtre placé vers la turbine. Remettez les couvercles surla turbine.REEMPLAZO DEL FILTROAtenciónEs conveniente que inspeccione el filtrode aire de la turbina para controlar siestá excesivamente sucio. Si se encuentrasucio, siga los pasos a continuación parareemplazarlo.Nunca haga funcionar la unidad sinlos filtros de aire. La suciedad puedeingresar en la unidad e interferir con sufuncionamiento.1. Presione las lengüetas de cada lado de la turbina pararetirar las tapas del filtro.Retire los filtros sucios de la turbina y reemplácelospor nuevos. Se debe colocar el lado suave del filtro deaire hacia la turbina.Fije las tapas de vuelta en la turbina.TROUBLESHOOTINGPROBLEM CAUSE SOLUTIONProblem A: Little or no material flow 1. Nozzle clogged.2. Suction tube clogged.3. Air vent on suction tube blocked.4. Material flow setting too low.5. Suction tube loose.6. No pressure build up in container.7. Air valve tube not functioning.8. Nozzle seal missing.9. Air filter clogged.10. Spray material too thick.1. Clean.2. Clean.3. Clean (see page 7)4. Increase material flow setting.5. Remove and replace as tightly as possible.6. Tighten container.7. Make sure both ends of the tube are connected andthe valve seal is in place.8. Replace nozzle.9. Change10. Thin.Problem B: Material leaking 1. Nozzle loose.2. Nozzle worn.3. Nozzle seal missing or worn.4. Material build-up on air cap and nozzle1. Tighten retaining ring.2. Replace.3. Replace nozzle.4. Clean.Problem C: Spray pattern too thick, runs and sags 1. Material flow setting too high.2. Air power setting too low.3. Applying too much material.4. Nozzle clogged.5. Air filter clogged.6. Too little pressure build-up in container.7. Spray material too thick.1. Decrease material flow setting.2. Increase air power setting.3. Adjust material flow or increase movement of spraygun.4. Clean.5. Change.6. Tighten container.7. Thin.Problem D: Spray gun spits 1. Material in container running out.2. Air filter clogged.3. Air valve tube disconnected.4. No pressure build up in container.1. Refill.2. Change.3. Reconnect both ends of the air tube.4. Tighten container or container lid.Problem E: Too much overspray 1. Gun too far from spray object.2. Air power setting too high.3. Material flow setting too high.1. Reduce distance (6”-8” is ideal).2. Decrease air power setting.3. Decrease material flow setting.Problem F: Pattern is very light and splotchy 1. Moving the spray gun too fast.2. Material flow setting too low.3. Air power setting too high.1. Adjust material flow or decrease movement of spraygun.2. Increase material flow setting.3. Decrease air power setting.