WAGO 750-630/040-001 Manual

Also see for 750-602/040-000: Manual

WAGO-I/O-SYSTEM 750 XTR Mounting 33750-630/040-001 SSI Interface Adjust XTRManualVersion 1.1.0Pos : 24 /All e Seri en (Allgemei ne Module)/Ü berschriften/Ebene 1/M onti eren - Ü bersc hrift 1 @ 3\mod_1225446744750_21.doc x @ 24900 @ 1 @ 15 MountingPos : 25.1 /Serie 750 (WAGO-I/O-SYST EM)/M ontieren/D emontieren/M ontagerei henfolge Ü berschrift 2 und Einl eitung @ 3\mod_1231770210031_21.doc x @ 25992 @ 2 @ 15.1 Mounting SequenceFieldbus couplers, controllers and I/O modules of the WAGO-I/O-SYSTEM 750are snapped directly on a carrier rail in accordance with the European standardEN 60175 (DIN 35).The reliable positioning and connection is made using a tongue and groovesystem. Due to the automatic locking, the individual devices are securely seatedon the rail after installation.Starting with the fieldbus coupler or controller, the I/O modules are mountedadjacent to each other according to the project design. Errors in the design of thenode in terms of the potential groups (connection via the power contacts) arerecognized, as the I/O modules with power contacts (blade contacts) cannot belinked to I/O modules with fewer power contacts.Pos : 25.2 /Serie 750 (WAGO-I/O-SYST EM)/Wic htige Erläuterungen (al te Str uktur)/Sic herheits- und s onstige Hinweise/Vorsic ht/Vorsic ht: Verletz ungsgefahr durc h sc harfkantige M esser kontakte! @ 6\mod_1256193279401_21.doc x @ 43414 @ @ 1Risk of injury due to sharp-edged blade contacts!The blade contacts are sharp-edged. Handle the I/O module carefully to preventinjury. Do not touch the blade contacts.Pos : 25.3 /Serie 750 (WAGO-I/O-SYST EM)/Wic htige Erläuterungen (al te Str uktur)/Sic herheits- und s onstige Hinweise/Achtung/Ac htung: I/O-Module nur in vorgesehener R eihenfolge stec ken! @ 6\mod_1256194177073_21.doc x @ 43429 @ @ 1Insert I/O modules only from the proper direction!All I/O modules feature grooves for power jumper contacts on the right side. Forsome I/O modules, the grooves are closed on the top. Therefore, I/O modulesfeaturing a power jumper contact on the left side cannot be snapped from thetop. This mechanical coding helps to avoid configuration errors, which maydestroy the I/O modules. Therefore, insert I/O modules only from the right andfrom the top.Pos : 25.4 /Serie 750 (WAGO-I/O-SYST EM)/Wic htige Erläuterungen (al te Str uktur)/Sic herheits- und s onstige Hinweise/Hinweis/Hi nweis : Bus absc hlus s XTR nic ht vergess en! @ 15\mod_1368426836647_21.doc x @ 119458 @ @ 1Don't forget the bus end module!Always plug a bus end module 750-600/040-000 onto the end of the fieldbusnode! You must always use this bus end module at all fieldbus nodes with theWAGO-I/O-SYSTEM 750 XTR fieldbus couplers/controllers to guarantee properdata transfer.Pos : 25.5 /Serie 750 (WAGO-I/O-SYST EM)/M ontieren/D emontieren/I/O-Modul e 750xxxx/0040xxxx 4g-5g @ 15\mod_1367558844291_21.doc x @ 118470 @ @ 1For vibration loads > 4g, observe the following installation instructions:• Use pan-head screws or blind rivets at least every 60 mm (12 mm pinspacing) to secure the DIN rail.• Make the open conductor length between strain relief and wire connectionas short as possible.• Use the reinforced end stop 249-197.Pos : 25.6 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1