Wayne-Dalton Optimal Installation, User Operation & Maintenance Manual

Also see for Confort: Installation, user operation & maintenance manual

Wayne-Dalton Optimal Installation, User Operation & Maintenance Manual Manual pdf 18 page image

18MAINTENANCE / PAINTING INSTRUCTIONS FOR PRE-PAINTED DOORSMAINTENANCEWhile factory-applied finishes on steel garage doors are durable, it is desirable to clean them on a routine basis. Some discoloration of the finish mayoccur when a door has been exposed to dirt-laden atmosphere for a period of time. Slight chalking may also occur as a result of direct exposure tosunlight. Cleaning the door will generally restore the appearance of the finish. To maintain an aesthetically pleasing finish of the garage door, an annualwashing of the door is recommended. A mild solution of detergent and water will aid in the removal of most dirt. The following solution mixture isrecommended: One cup of Tide™, or other common detergents, which contain less than 0.5% phosphate, dissolved into five gallons of warm water.CAUTION: NEVER MIX CLEANSERS OR DETERGENTS WITH BLEACH.SURFACE PREPARATION FOR PAINTINGWax on the surface must be removed or paint peeling/flaking will result. To remove this wax, it will be necessary to lightly scuff the surface with a finesteel wool pad, saturated with soapy water. A final wipe and rinse should be done with clean water only, to remove any loose particles and any soapyfilm residue. Surface scratches, which have not exposed the metal substrate, can be lightly buffed or sanded with 0000 steel wool or no. 400 sand paperto create a smoother surface. Care must be taken to not expose the substrate under the paint (see NOTE no. 2). Once the substrate is exposed, thelikelihood for rusting is greatly increased. See the following paragraph if metal substrate is observed. The exposed substrate must be treated to preventrust from forming (see NOTE no. 2). Sand the exposed area lightly and paint with a high quality metal primer, specifically intended for galvanizedsurfaces, to protect the area from corrosion. Follow drying time on primer can label before applying topcoat. The surface of the factory-applied finish, thatis being painted, must not be too smooth, or the paint will not adhere to it (see NOTE no. 2). It is advisable to test in an inconspicuous area, to evaluateadhesion. If poor adhesion is observed, surface preparation for painting the factory- applied finish must be repeated until desired results are achieved.Again, care must be taken to not expose the substrate under the paint.PAINTINGAfter the surface has been properly prepared it must be allowed to dry thoroughly, then coated immediately with premium quality latex house paint.Follow the paint label directions explicitly. Oil base, or solvent base paints are not recommended. Please note that if substrate is exposed and notproperly primed, painting with latex paint may cause accelerated rusting of the steel in the exposed area.NOTE:1. Repainting of finish painted steel doors cannot be warranted, as this condition is totally beyond the door manufacturer’s control.2. If the finish painted steel door surface has a textured surface representing wood grain, stucco, etc., this step should not be attempted as danger ofexposing substrate is greatly increased.3. Consult a professional coatings contractor if in doubt about any of the above directions.4. Follow directions explicitly on the paint container labels for proper applications of coatings and disposal of containers. Pay particular attention toacceptable weather and temperature conditions in which to paint.DÉCOR LITES ACRYLIC GLAZING CLEANING INSTRUCTIONS:1. Clean acrylic glazing with nonabrasive soap or detergent and plenty of water. Use your bare hands to feel and dislodge any caked on particles a soft,grit-free cloth, sponge or chamois may be used to wipe the surface. Do not use hard or rough cloths that will scratch the acrylic glazing. Dry glazing witha clean damp chamois.2. Kerosene may be used to remove grease and oil. When using kerosene for cleaning purposes, make sure that you are familiar with its proper ties,using it only in a well ventilated area away from any sources of sparks and/or fire.3. DO NOT USE: Window cleaning fluids, scouring compounds, gritty cloths, gasoline, or solvents such as alcohol, acetone, carbon tetrachloride, etc.