Wayne-Dalton Torquemaster 9100 Installation Instructions And Owner's Manual

Also see for Torquemaster Plus 9100: Installation instructions and owner's manual

Contents

Wayne-Dalton Torquemaster 9100 Installation Instructions And Owner's Manual Manual pdf 16 page image

DRAWBAR OPERATOR HOOK-UP CHART,STANDARD LIFT FOR 12” AND 15” RADIUSOPERATOR MODELS TYPE OF ARM BEING USED REF. ILLUSTRATIONSQUANTUM/CLASSIC CURVED / STRAIGHT FIG 6LINEAR STRAIGHT / CURVED FIG 5LIFTMASTER (SEARS) CURVED / STRAIGHT FIG 6GENIE CURVED / STRAIGHT FIG 6 Or FIG 5DRAWBAR OPERATOR HOOK-UP CHART FOR LOW HEADROOMOPERATORMODELS TYPE OF ARM BEING USEDPREFERREDHOOKUP REF. ILLUSTRA-TIONS OPTIONALHOOK-UP REF. ILLUSTRA-TIONSQUANTUM /CLSSSIC CURVED /STRAIGHT FIG. 8 STRAIGHT FIG. 7LINEAR STRAIGHT FIG. 7 N/A N/ALIFTMASTER(SEARS) CURVED /STRAIGHT FIG. 8 STRAIGHT FIG. 7GENIE CURVED /STRAIGHT FIG. 8 STRAIGHT FIG. 7FIG 112” or 15”FIG 2HorizontaltrackLevelHigh arcTop sectionHorizontalradiusHigh arcFIG 4FIG 3TorqueMaster ®counterbalanceVerticalcenter lineFrom stepTypical 1/2”-1”above high arcHigh arc lineHeaderTop sectionLow headroom trackLevelCut straight arm toaccomplish trolleysettingFIG 6FIG 5Curved armCurved armCut straight arm toaccomplish trolleysettingStraight armStraight armCurved armStraight armFIG 8FIG 7Cut straight arm toaccomplish trolley settingInside LockTools: Power drill, 7/16” Socket driver, Tape measureInstall the inside lock on the second section of the door. Secure the lock to the section with (4)1/4”-20 x 11/16” self drilling screws. Square the lock assembly with the door section, and alignwith the square hole in the vertical track. The inside lock should be spaced approximately 1/8”away from the section edge.IMPORTANT: INSIDE LOCK(S) MUST BE REMOVED OR MADE INOPERATIVE IN THE UNLOCKEDPOSITION IF AN OPERATOR IS INSTALLED ON THIS DOOR.Second section 1/8”Inside lockEnd cap(4) 1/4”-20 x 11/16”Self drilling screwsSquare hole invertical trackPull Down RopeTools: Power drill, 1/8” Drill bit, Tape measureWARNINgWARNINgDO NOT INSTALL PuLL DOWN ROPE ON DOORS WITH OPERATORS. CHILDRENMAy BECOME ENTANgLED IN THE ROPE CAuSINg SEvERE OR FATAL INJuRy.Measure and mark the jamb approximately 48” to 50” (1220 to 1270 mm) from floor on theright or left side of jamb. Drill 1/8” pilot hole for no. 6 screw eye. Tie the pull down rope to theno. 6 screw eye and to the bottom corner bracket, as shown.Bottom cornerbracketPull downropeNo. 6 Screw eyePull downrope48” to 50”From floorStep PlateTools: Tape measure, Power drill, 7/16” Drill bit, 7/16” Wrench, Phillipshead screwdriverMake one mark 1” (25 mm) up from the center of bottom edge of the bottom section andanother mark 2-3/16” (56 mm) up from the first mark.NOTE: Top of step plate can be no higher than 8” from the bottom of the door.Drill a 7/16” (11 mm) hole through the section at each mark and insert the outside step plate.16Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer,refer to your local yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com