Wayne-Dalton Torquemaster 9100 Installation Instructions And Owner's Manual

Also see for Torquemaster Plus 9100: Installation instructions and owner's manual

Contents

Wayne-Dalton Torquemaster 9100 Installation Instructions And Owner's Manual Manual pdf 3 page image

Important Safety InstructionsDEFINITION OF kEy WORDS uSED IN THIS MANuAL:WARNINgWARNINgINDICATES A POTENTIALLy HAzARDOuS SITuATION WHICH; IF NOT AvOIDED,COuLD RESuLT IN SEvERE OR FATAL INJuRy.CAuTION: PROPERTY DAMAGE OR INJURY CAN RESULT FROM FAILURE TO FOLLOWINSTRUCTIONS.IMPORTANT: REQUIRED STEP FOR SAFE AND PROPER DOOR OPERATION.NOTE: Information assuring proper installation of the door.READ THESE INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING INSTALLATION. IF IN QUESTIONABOUT ANY OF THE PROCEDURES, DO NOT PERFORM THE WORK. INSTEAD, HAVE A TRAINEDDOOR SYSTEMS TECHNICIAN DO THE INSTALLATION OR REPAIRS.1. READ AND FOLLOW ALL INSTALLATION INSTRuCTIONS.2. Wear protective gloves during installation to avoid possible cuts from sharp metal edges.3. It is always recommended to wear eye protection when using tools, otherwise eye injurycould result.4. Avoid installing your new door on windy days. Door could fall during the installation caus-ing severe or fatal injury.5. Doors 12’-0” wide and over should be installed by two persons, to avoid possible injury.6. Operate door only when it is properly adjusted and free from obstructions.7. If a door becomes hard to operate, inoperative or is damaged, immediately have neces-sary adjustments and/ or repairs made by a trained door system technician using propertools and instructions.8. DO NOT stand or walk under a moving door, or permit anybody to stand or walk under anelectrically operated door.9. DO NOT place fingers or hands into open section joints when closing a door. Use lifthandles/ gripping points when operating door manually.10. DO NOT permit children to operate garage door or door controls. Severe or fatal injurycould result should the child become entrapped between the door and the floor.11. Due to constant extreme spring tension, do not attempt any adjustment, repair or altera-tion to any part of the door, especially to springs, spring brackets, bottom corner brackets,fasteners, counterbalance lift cables or supports. To avoid possible severe or fatal injury,have any such work performed by a trained door systems technician using proper toolsand instructions.12. On electrically operated doors, pull down ropes must be removed and locks must beremoved or made inoperative in the open (unlocked) position.13. Top section of door may need to be reinforced when attaching an electric opener. Checkdoor and/ or opener manufacturer’s instructions.14. Visually inspect door and hardware monthly for worn and or broken parts. Check toensure door operates freely.15. Test electric opener’s safety features monthly, following opener manufacturer’s instruc-tions.16. NEVER hang tools, bicycles, hoses, clothing or anything else from horizontal tracks. Tracksystems are not intended or designed to support extra weight.17. This door may not meet the building code wind load requirements in your area. For yoursafety, you will need to check with your local building official for wind load code require-ments and building permit information.After installation is complete, fasten this manual near the garage door.IMPORTANT: STAINLESS STEEL OR PT2000 COATED LAG SCREWS MUST BE USED WHENINSTALLING CENTER BEARING BRACKETS, END BRACKETS, JAMB BRACKETS, DRAWBAR OP-ERATOR MOUNTING/ SUPPORT BRACKETS AND DISCONNECT BRACKETS ON TREATED LUMBER(PRESERVATIVE-TREATED). STAINLESS STEEL OR PT2000 LAG SCREWS ARE NOT NECESSARYWHEN INSTALLING PRODUCTS ON UN-TREATED LUMBER.NOTE: It is recommended that 5/16” lag screws are pilot drilled using a 3/16” drill bit, prior tofastening.IMPORTANT: WHEN INSTALLING 5/16” LAG SCREWS USING AN ELECTRIC DRILL/ DRIVER, THEDRILL/ DRIVERS CLUTCH MUST BE SET TO DELIVER NO MORE THAN 200 IN-LBS OF TORQUE.FASTENER FAILURE COULD OCCUR AT HIGHER SETTINGS.WARNINgWARNINgPRIOR TO WINDINg OR MAkINg ADJuSTMENTS TO THE SPRINgS, ENSuREyOu’RE WINDINg IN THE PROPER DIRECTION AS STATED IN THE INSTAL-LATION INSTRuCTIONS. OTHERWISE, THE SPRINg FITTINgS MAy RELEASEFROM SPRINg IF NOT WOuND IN THE PROPER DIRECTION AND COuLDRESuLT IN SEvERE OR FATAL INJuRy.IMPORTANT: RIGHT AND LEFT HAND IS ALWAYS DETERMINED FROM INSIDE THE BUILDINGLOOKING OUT.Tools Required• Power drill• Drill bits: 1/8”, 3/16”,7/16”• Ratchet wrench• Socket driver: 7/16”• Sockets: 7/16”, 1/2”,9/16”, 5/8”• Socket extension: 3”• Phillips headscrewdriver• Flat tip screwdriver• Pliers/Wire cutters• Needle nose pliers• Locking Pliers• (2) Vice clamps• Wrenches: 7/16”,1/2”, 9/16”, 5/8”• Hammer• Tape measure• Step Ladder• Level• Pencil• Leather gloves• Safety glassesPackage ContentsNOTE: Depending on the door model, some parts listed will not be supplied if not required. RearBack Hangs may not be included with your door.Door sections (as required)TorqueMaster® spring tubeQuick Install flag angles RH/LH(as required)Fully Adjustable flag angles RH/LH(as required)(2) Horizontal track angles (as required)Horizontal tracks RH/LHVertical tracks RH/LHQuick install jambbrackets (as required)Fully adjustable jambbrackets (as required)(2) Top fixture rollerslides (as required) Winload jambbrackets (as required)Track rollers(as required)(2) Top fixture bases(as required) (2) Top fixture slides(as required) (2) Top fixture rollerslides (as required)Strut (U-shaped)(if included)Strut(A-symmetrical)(if included) Center bracketbushing assemblyEnd brackets RH/LHRatchet PawlENGAGED SIDE VIEWNDERNEATH VIEWWeatherstrips &nails (If included)Reinforcementbrackets(as required)Cable drumassemblies RH/LH Drum wrapsRH/LH (as required)Loose windingshaft (singlespring only)3Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer,refer to your local yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.comPre-Installation