6An ongoing program of product improvement m ay require u s to changespecications without notice. WS-GFT, Revised April 2015.Doc no: M0053.02info@woodstone-corp.com or visit woodstone-corp.comwood stone corporation1801 w. bakerview rd.bellingham, wa 98226 usatf. 800.988.8103t. 360.650.1111f. 360.650.1166Tandoor Installation and Operation ManualREV:LEGEND:PART #: WS-GFT-35-RND35" Tandoor. All ShapesGeneral Arrangement10/14/2013 bena 1DWN BY:SHEET:Bellingham, WA 360/650-1111 www.woodstone-corp.comDIMENSIONS ARE IN INCHESTOLERANCES: LINEAR ±1/2 [±10mm], ANGULAR ±2°UNLESS NOTED OTHERWISE\\woodstone.net\dfs\CAD\0 Pn\WS Top Level\WS-GFT-35_General_Arrangement-1.dftTHE INFORMATION CONTAINED IN THIS DRAWING IS THESOLE PROPERTY OF WOOD STONE CORPORATIONANY REPRODUCTION OR USE IN PART OR AS A WHOLEWITHOUT THE WRITTEN PERMISSION OF WOOD STONE ISPROHIBITEDAN ONGOING PROGRAM OF PRODUCT IMPROVEMENTMAY REQUIRE US TO CHANGE SPECIFICATIONSWITHOUT NOTICE.DATE:G GAS INLET: 1/2" NPT40,000 BTU, NG40,000 BTU, LP1 of 1G G34 3/4"880mmO 13"330mmOpeningO 13"330mmOpening40 3/4"1040mm34 3/4"880mmGO 13"330mmOpening34 3/4"880mm14 1/4"360mm33 3/4"860mm6 1/4"160mm24 1/2"620mm24 3/4"630mmPlan view (Round)LEGEND:PART #: WS-GFT-35-RND35" Tandoor. All ShapeGeneral Arrangement10/14/2013 benaDWN BY:SHEET:Bellingham, WA 360/650-1111 www.woodstone-corp.comDIMENSIONS ARE IN INCHESTOLERANCES: LINEAR ±1/2 [±10mm], ANGULAR ±2°UNLESS NOTED OTHERWISE\\woodstone.net\dfs\CAD\0 Pn\WS Top Level\WS-GFT-35_General_Arrangement-1.dftTHE INFORMATION CONTAINED IN THIS DRAWING IS THESOLE PROPERTY OF WOOD STONE CORPORATIONANY REPRODUCTION OR USE IN PART OR AS A WHOLEWITHOUT THE WRITTEN PERMISSION OF WOOD STONE ISPROHIBITEDAN ONGOING PROGRAM OF PRODUCT IMPROVEMENTMAY REQUIRE US TO CHANGE SPECIFICATIONSWITHOUT NOTICE.DATE:G GAS INLET: 1/2" NPT40,000 BTU, NG40,000 BTU, LP1 of 1G GO 13"330mmOpeningO 13"330mmOpening40 3/4"1040mmGO 13"330mmOpening33 3/4"860mm6 1/4"160mm24 1620m24 3/4"630mmSide view (Round)REV:LEGEND:PART #: WS-GFT-35-RND35" Tandoor. All ShapesGeneral Arrangement10/14/2013 bena 1DWN BY:SHEET:Bellingham, WA 360/650-1111 www.woodstone-corp.comDIMENSIONS ARE IN INCHESTOLERANCES: LINEAR ±1/2 [±10mm], ANGULAR ±2°UNLESS NOTED OTHERWISE\\woodstone.net\dfs\CAD\0 Pn\WS Top Level\WS-GFT-35_General_Arrangement-1.dftTHE INFORMATION CONTAINED IN THIS DRAWING IS THESOLE PROPERTY OF WOOD STONE CORPORATIONANY REPRODUCTION OR USE IN PART OR AS A WHOLEWITHOUT THE WRITTEN PERMISSION OF WOOD STONE ISPROHIBITEDAN ONGOING PROGRAM OF PRODUCT IMPROVEMENTMAY REQUIRE US TO CHANGE SPECIFICATIONSWITHOUT NOTICE.DATE:G GAS INLET: 1/2" NPT40,000 BTU, NG40,000 BTU, LP1 of 1G G34 3/4"880mmO 13"330mmOpeningO 13"330mmOpening40 3/4"1040mm34 3/4"880mmGO 13"330mmOpening34 3/4"880mm14 1/4"360mm33 3/4"860mm6 1/4"160mm24 1/2"620mm24 3/4"630mmFront view (Round)REV:PART #: WS-GFT-35-RND10/14/2013 bena 1DWN BY:SHEET:ne-corp.comDATE:1 of 1G G34 3/4"880mmO 13"330mmOpeningGO 13"330mmOpening34 3/4"880mm14 1/4"360mm6 1/4"160mm24 1/2"620mm24 3/4"630mmPlan view (Square)G34 3/4"880mmO 13"330mmOpeningG14 1/4"360mm24 1/2"620mm24 3/4"630mmPlan view (Octagonal)WS-GFT-35 (ROUND, OCTAGONAL AND SQUARE MODELS)GFT-35 SPECIFICATIONSNote: Side and frontview dimensions arethe same for the Round,Square and Octagonalmodels�UTILITY SPECIFICATIONSGas: 1/2-inch FNPT gas inlet40,000 BTU/hr Natural Gas (NG) OR Propane (LP)Gas type must be specified when ordering� Gas connection shouldbe made using an approved flexible connector and the unit must berestrained in accordance with all relevant local and/or national codes�Gas connection is made beneath unit at rear�VentingThis appliance must be installed under a Listed Type 1 exhaust hood, inaccordance with all relevant local and national codes, and in a manneracceptable to the authority having jurisdiction� Please contact WoodStone for more detailed information�Shipping weight:950 lbs.Air intake: Do notfacade or cover over