Yaesu FT-2000D - MENU MODE LIST Manual

Also see for FT-2000D: Brochure & specs Operating manual Update Update Update

Contents

Yaesu FT-2000D - MENU MODE LIST Manual Manual pdf 13 page image

Page 124 FT-2000D O PERATING M ANUALMODE-SSB GROUP084 J3E MIC SELFunction: Selects the microphone to be used on the SSBmodes (LSB and USB).Available Values: Frnt / dAtA / PCDefault Setting: FrntFrnt (FRONT): Selects the microphone connected tothe front panel’s MIC jack while usingthe SSB modes.dAtA: Selects the microphone connected topin 1 of the PACKET Jack while us-ing the SSB modes.PC: This parameter is for future expansionof this transceiver’s capabilities, but atthis time is not supported.085 J3E TX BPFFunction: Selects the audio passband of the DSP modula-tor on the SSB mode.Available Values: 1-30 / 1-29 / 2-28 / 3-27 / 4-26 / 30001-30: 50-3000(Hz)1-29: 100-2900(Hz)2-28: 200-2800(Hz)3-27: 300-2700(Hz)4-26: 400-2600(Hz)3000: 3000WBDefault Setting: 3-27 (300-2700 Hz)N OTE:The apparent power output, when using the widest band-widths, may seem lower. This is normal, and it occurs be-cause the available transmitter power is distributed over awider bandwidth. The greatest compression of power out-put, conversely, occurs when using the “4-26” setting (400-2600 Hz), and this setting is highly recommended for con-test or DX pile-up work.086 J3E LSB CARFunction: Adjusts the receiver carrier point for the Mainband’s (VFO-A) LSB mode.Available Values: –200 Hz ~ +200 Hz (10 Hz/steps)Default Setting: 0 Hz087 J3E USB CARFunction: Adjusts the receiver carrier point for Mainband’s (VFO-A) USB mode.Available Values: –200 Hz ~ +200 Hz (10 Hz/step)Default Setting: 0 Hz088 J3E SLSB CRFunction: Adjusts the receiver carrier point for the Subband’s (VFO-B) LSB mode.Available Values: –200 Hz ~ +200 Hz (10 Hz/step)Default Setting: 0 Hz089 J3E SUSB CRFunction: Adjusts the receiver carrier point for Sub band’s(VFO-B) USB mode.Available Values: –200 Hz ~ +200 Hz (10 Hz/step)Default Setting: 0 HzRX AUDIO GROUP090 rout AGC SLPFunction: Selects the gain curve of the AGC amplifier.Available Values: nor / SLPDefault Setting: nornor (NORMAL): The AGC output level will follow alinear response to the antenna inputlevel, while AGC is activated.SLP (SLOPED): The AGC output level will increaseat 1/10 the rate of the antenna inputlevel, while AGC is activated.MENU M ODENORMALInput SignalAudio Output SLOPE091 rout HEADPHNFunction: Selects one of three audio mixing modes whenusing headphones during Dual Receive operation.Available Values: SEP / Con1 / Con2Default Setting: SEPSEP (SEPARATE): Audio from the Main (VFO-A)receiver is heard only in the leftear, and Sub (VFO-B) receiveraudio solely in the right ear.Con1 (COMBINE 1): Audio from both Main (VFO-A) and Sub (VFO-B) receiverscan be heard in both ears, butSub (VFO-B) audio is attenu-ated in the left ear and Main(VFO-A) audio is attenuated inthe right ear.Con2 (COMBINE 2): Audio from both Main (VFO-A) and Sub (VFO-B) receiversis combined and heard equallyin both ears.