Yaesu FTM-10R Technical Supplement

Also see for FTM-10R: Brochure & specs Manual Operating manual Easy Programming Guide

Contents

11FTM-10R/E Technical SupplementPLL Reference Frequency1. Press the key repeatedly to display the fre-quency.2. Set the transceiver frequency to 440.050 MHz.3. Press and hold the key for one second toenter the Menu mode.4. Rotate the DIAL knob to select Menu Item "F44 TXF44 TXF44 TXF44 TXF44 TXPOWERPOWERPOWERPOWERPOWER".5. Press the  key, then rotate the DIAL knob to select"LOW".6. Press the key to save the new setting andexit the Menu mode.7. Press the key repeatedly to display theAlignment Menu.8. Press the  key repeatedly to select Alignment MenuItem "A-0 REF. xxxA-0 REF. xxxA-0 REF. xxxA-0 REF. xxxA-0 REF. xxx".9. Key the transmitter and adjust the DIAL knob, if nec-essary, so the counter frequency is within 100 Hz of435.050 MHz.10.Press the key to save the new setting andexit the Alignment Menu mode.RF Front-end Tuning1. Connect the DC voltmeter to TP1801 on the MAIN unit,then inject a 439.050 MHz signal at a level of +10dBμ(with 1 kHz modulation ± 3.5 kHz deviation) from theRF signal generator.2. Press the key repeatedly to display the fre-quency.3. Set the transceiver frequency to 439.050 MHz.4. Press the key repeatedly to display theAlignment Menu.5. Press the  key repeatedly to select Alignment MenuItem "A-1 TUN. xxxA-1 TUN. xxxA-1 TUN. xxxA-1 TUN. xxxA-1 TUN. xxx".6. Adjust the DIAL knob so that the DC voltmeter read-ing is lower than the maximum deflection.7. Press the key repeatedly to display the fre-quency.8. Set the transceiver frequency to 145.050 MHz.9. Press the key repeatedly to display theAlignment Menu.10.Press the  key repeatedly to select Alignment MenuItem "A-1 TUN. xxxA-1 TUN. xxxA-1 TUN. xxxA-1 TUN. xxxA-1 TUN. xxx".11.Adjust the DIAL knob so that the DC voltmeter, read-ing is lower than the maximum deflection.12.Press the key to save the new setting andexit the Alignment Menu mode.VHF Transmitter Output1. Press the key repeatedly to display the fre-quency.2. Set the transceiver frequency to 146.050 MHz.3. Press and hold the key for one second toenter the Menu mode.4. Rotate the DIAL knob to select Menu Item "F44 TXF44 TXF44 TXF44 TXF44 TXPOWERPOWERPOWERPOWERPOWER".5. Press the  key, then rotate the DIAL knob to select"LOW".6. Press the key to save the new setting andexit the Menu mode.7. Press the key repeatedly to display theAlignment Menu.8. Press the  key repeatedly to select Alignment MenuItem "A-2 PWR. xxxA-2 PWR. xxxA-2 PWR. xxxA-2 PWR. xxxA-2 PWR. xxx".9. Key the transmitter and rotate the DIAL knob to adjusttransmit power to 5 ± 0.3 Watts on the wattmeter.10.Press the key to save the new setting andexit the Alignment Menu mode.11.To change the TX Power to "MID", just repeat steps 3through 6 above, rotating the DIAL knob to select "MID"in step 5 above.12.Press the key repeatedly to display theAlignment Menu mode.13.Press the key repeatedly to select Align-ment Menu Item "A-2 PWR. xxxA-2 PWR. xxxA-2 PWR. xxxA-2 PWR. xxxA-2 PWR. xxx".14.Key the transmitter and rotate the DIAL knob to adjusttransmit power to 20 ± 0.5 Watts on the wattmeter.15.Press the key to save the new setting andexit the Alignment Menu mode.16.To change the TX Power to "HIGH", just repeat steps 3through 6 above, rotating the DIAL knob to select "HIGH"in step 5 above.17.Press the key repeatedly to display theAlignment Menu mode.18.Press the key repeatedly to select Align-ment Menu Item "A-2 PWR. xxxA-2 PWR. xxxA-2 PWR. xxxA-2 PWR. xxxA-2 PWR. xxx".19.Key the transmitter and rotate the DIAL knob to adjusttransmit power to 50 ± 0.5 Watts on the wattmeter.20.Press the key to save the new setting andexit the Alignment Menu mode.Alignment