Yamaha RX-V365 Owner's Manual

Also see for RX-V365: Service manual Owner's manual Connection guide Owner's manual Owner's manual

34 EnSet menu■ Test tone TESTUse this feature to make adjustments for “CENTER GEQ”while listening to a test tone.Use this feature to adjust the output level of the LFE (low-frequency effect) channel according to the capacity ofyour subwoofer or headphones.Control range: –20 dB to 0 dB*Control step: 1 dB■ Speaker LFE SP LFEAdjusts the speaker LFE level.■ Headphone LFE HP LFEAdjusts the headphone LFE level.Notes• Depending on the settings of “BASS OUT” (see page 32), some signalsmay not be output at the SUBWOOFER OUTPUT jack.• The LFE channel carries low-frequency special effects which are onlyadded to certain scenes.• This setting is effective when the input signal contains the LFE channel.Use this feature to select the amount of dynamic rangecompression to be applied to your speakers orheadphones. This setting is effective only when this unit isdecoding Dolby Digital and DTS signals.■ Speaker dynamic range SP D.RAdjusts the speaker compression.■ Headphone dynamic range HP D.RAdjusts the headphone compression.Use this feature to adjust the overall audio settings of thisunit.■ Mute type MUTE TYP.Use this feature to adjust how much the mute functionreduces the output volume (see page 20).■ Audio delay A.DELAYUse this feature to delay the sound output and synchronizeit with the video image. This may be necessary for certainLCD monitors or projectors.Control range: 0 ms* to 160 msControl step: 1 ms■ Maximum volume MAX VOL.Use this feature to set the maximum volume levelregardless of the original volume range. This feature isuseful to avoid the unexpected loud sound.Control range: +16 dB*, +10 dB to –30 dBControl step: 5 dBNote• The “MAX VOL.” setting takes priority over the “INI.VOL.” setting. Forexample, if “INI.VOL.” is set to –20 dB and “MAX VOL.” is set to –30dB, the volume level is automatically set to –30 dB when you turn on thepower of this unit next time.■ Initial volume INI.VOL.Use this feature to set the volume level when the power ofthis unit is turned on.Choices: Off*, –80 dB to +16 dBControl step: 1 dBNote• The “MAX VOL.” setting takes priority over the “INI.VOL.” setting.Use this menu to reassign the input jacks, select the inputmode or rename the input source.y• Initial settings are indicated by (*) in this following each parameter.Use this feature to assign the input jacks according to thecomponent to be used if the initial settings of this unit donot correspond to your needs.Choices: CD, MD/CD-R, DVD, DTV/CBL, V-AUX, DVRInitial setting:IN (1) (COAXIAL jack): DVDIN (2) (OPTICAL (DTV/CBL) jack): DTV/CBLIN (3) (OPTICAL (CD) jack): CDNotes• You cannot select a specific item more than once.• You cannot assign the same input source to both “IN (2)” and “IN (3).”For example, you assign “CD” to “IN (2),” “–––” appears in “IN (3).”• Once the input jacks are reassigned, you can select the correspondingcomponent by using NINPUT l / h (or the input selector buttons(e) on the remote control).Choice FunctionOFF* Stops test tones and output the currently.ON Outputs test tones from the center and from leftspeakers.Low-frequency effect level E)LFE LEVELDynamic range F)D.RANGEChoice FunctionMIN Adjusts the dynamic range to narrow.STD Adjusts the dynamic range to medium.MAX* Preserves the greatest amount of dynamic range.Audio settings G)AUDIO SETChoice FunctionFULL* Completely mutes all the audio output.-20dB Reduces the current volume by 20 dB.2 INPUT MENUInput assignment A)INPUT ASSIGN