ABB ACS880-04XT manuals
ACS880-04XT
Table of contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Contents of this chapter
- Related manuals
- Selecting the main contactor (breaker)
- Selecting the supply transformer
- Additional notes
- A drive with a 12-pulse diode supply unit
- Examining the compatibility of the motor and drive
- Availability of du/dt filter and common mode filter by drive type
- Additional requirements for non-ABB high-output and IP23 motors
- Additional data for calculating the rise time and the peak line-to-line voltage
- Selecting the power cables
- Alternative power cable types
- Not allowed power cable types
- Additional US requirements
- Selecting the control cables
- Routing the cables
- Separate control cable ducts
- Implementing thermal overload and short circuit protections
- Multidrive modules
- Implementing a motor temperature sensor connection
- Implementing a ground fault protecting function
- Implementing the Emergency stop function
- Implementing the Prevention of unexpected start-up function
- Implementing the Power-loss ride-through
- Implementing a bypass connection
- Applicable standards
- Markings
- EMC compliance (IEC/EN 61800-3:2004 + A2012)
- Category C3
- EU Declaration of Conformity (Machinery Directive)
- UL and CSA checklist
- Disclaimers
ACS880-04XT
Table of contents
- List of related manuals
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- What this chapter contains
- Licensing
- Contents of the manual
- Local control vs. external control
- External control
- Operating modes of the drive
- Speed control mode
- Contents of this chapter
- Drive start-up
- ESP application minimum configuration
- Backspin supervision
- Backspin speed observer constraints
- Starting the motor
- Kick-start
- Current pulse-start
- ESP production mode
- Automatic process control mode
- Underload and overload protection
- Underload ride through recovery sequence
- Overload recovery sequence
- Motor voltage control
- Pump impeller cleaning
- Pump curves
- Drive configuration and programming
- Adaptive programming
- Control interfaces
- Programmable relay outputs
- Fieldbus control
- Master/follower functionality
- External controller interface
- Control of a supply unit (LSU)
- Motor control
- Constant speeds/frequencies
- Speed controller autotune
- Oscillation damping
- Resonance frequency elimination
- Encoder support
- Jogging
- Scalar motor control
- Autophasing
- Flux braking
- DC magnetization
- Hexagonal motor flux pattern
- Application control
- Motor potentiometer
- Mechanical brake control
- DC voltage control
- Voltage control and trip limits
- Brake chopper
- Safety and protections
- Motor thermal protection
- Thermal protection of motor cable
- Automatic fault resets
- Other programmable protection functions
- Diagnostics
- Energy saving calculators
- Miscellaneous
- User lock
- Reduced run function
- du/dt filter support
- Factory macro
- Default control connections for the Factory macro
- Hand/Auto macro
- Default control connections for the Hand/Auto macro
- PID control macro
- Default parameter settings for the PID control macro
- Default control connections for the PID control macro
- Sensor connection examples for the PID control macro
- Torque control macro
- Default control connections for the Torque control macro
- Sequential control macro
- Selection of constant speeds
- Default control connections for the Sequential control macro
- Fieldbus control macro
- Terms and abbreviations
- Summary of parameter groups
- Parameter listing
- Input references
- Warnings and faults
- Control and status words
- System info
- ESP signals
- Standard DI, RO
- Standard DIO, FI, FO
- Standard AI
- Standard AO
- I/O extension module 1
- I/O extension module 2
- I/O extension module 3
- Operation mode
- Start/stop/direction
- Start/stop mode
- Speed reference selection
- Speed reference ramp
- Speed reference conditioning
- Speed control
- Torque reference chain
- Frequency reference chain
- Limits
- Fault functions
- Supervision
- Generic timer & counter
- Load analyzer
- User load curve
- Process PID set 1
- Process PID set 2
- Energy efficiency
- Monitoring/scaling settings
- Data storage
- Panel port communication
- Fieldbus adapter (FBA)
- FBA A settings
- FBA B settings
- Embedded fieldbus
- DDCS communication
- D2D and DDCS transmit data
- D2D and DDCS receive data
- ESP control
- ESP reference setup
- ESP automatic control
- Load protection
- Voltage control
- Pump cleaning
- Q-H pump curves
- Feedback selection
- Encoder module settings
- Encoder 1 configuration
- Encoder 2 configuration
- LSU control
- HW configuration
- System
- User motor parameters
- Motor data
- Safety
- Fieldbus addresses
- Parameter groups 1...9
- Parameter groups 10...99
- Pure events
- Other data loggers
- QR Code generation for mobile service application
- Warning messages
- Fault messages
- Connecting the fieldbus to the drive
- Setting up the embedded fieldbus interface
- Setting the drive control parameters
- Basics of the embedded fieldbus interface
- Control word and Status word
- Register addressing
- About the control profiles
- The ABB Drives profile
- Status Word
- State transition diagram
- References
- Actual values
- Modbus holding register addresses
- The Transparent profile
- Modbus function codes
- Exception codes
- Coils (0xxxx reference set)
- Discrete inputs (1xxxx reference set)
- Error code registers (holding registers 400090...400100)
- Basics of the fieldbus control interface
- Contents of the fieldbus Control word (ABB Drives profile)
- Contents of the fieldbus Status word (ABB Drives profile)
- The state diagram (ABB Drives profile)
- Setting up the drive for fieldbus control
- Parameter setting example: FPBA (PROFIBUS DP)
- Speed reference source selection I
- Speed reference source selection II
- Speed reference ramping and shaping
- Motor feedback configuration
- Load feedback and position counter configuration
- Speed error calculation
- Speed controller
- Torque reference source selection and modification
- Operating mode selection
- Reference selection for torque controller
- Torque limitation
- Torque controller
- Frequency reference selection
- Frequency reference modification
- Process PID setpoint and feedback source selection
- Process PID controller
- Master/Follower communication I (Master)
- Master/Follower communication II (Follower)
- Product and service inquiries
manualsdatabase
Your AI-powered manual search engine