Keysight Technologies N9030B manuals
N9030B
Table of contents
- safety notices
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- What You Will Find in This Chapter
- Keysight PXA Signal Analyzer Overview
- Instrument Option Descriptions
- Signal Analyzer Accessories
- Ohm Load
- Broadband Preamplifiers and Power Amplifiers
- Before You Start Troubleshooting
- Lithium Battery Disposal
- ESD Information
- Handling of Electronic Components and ESD
- Instrument Maintenance
- Battery Information
- Service Equipment You Will Need
- Front End Controller Troubleshooting Kit
- USB Keyboard and Mouse
- Required Test Equipment List
- After an Instrument Repair
- Contacting Keysight Technologies
- Instrument Serial Numbers
- How to Return Your Instrument for Service
- Other Packaging
- Check the Basics
- PXA Instrument Boot Up Process
- Typical instrument boot-up process flow
- Potential Problems During Boot Process
- Green Power On LED Does Not Illuminate
- Fan(s) Are Not Operating
- No Keysight Splash Screen Displayed
- Instrument Hangs at the Keysight Splash Screen
- Instrument Cannot Completely Load or Run the Operating System
- Verify LCD Backlight Functionality
- Verify Video Signal Path Integrity
- Fails an Initial Alignment
- Signal Level Verification
- Input Frequencies > 3.6 GHz
- Introduction
- Event and Condition Categories
- Event Message Format
- Event Queues
- Advisory Messages
- Event Messages
- Operation Complete Event
- to –399, Device-Specific Errors
- Settings Conflict Errors
- to –299, Execution Errors
- to –199, Command Errors
- error
- Condition Messages
- Condition Errors 101 to 199, Measurement Integrity
- Condition Errors 201 to 299, Signal Integrity
- Condition Errors 301 to 399, Uncalibrated Integrity
- Condition Errors 401 to 499, Power
- Condition Errors 501 to 599, Frequency
- Condition Errors 601 to 699, Error Summaries
- Condition Errors 701 to 799, Operation
- Condition Errors 801 to 899, Temperature
- RF Section Description
- A9 Input Attenuator A
- A11 Low Band Switch
- A13 RF Front End Assembly
- Troubleshooting
- Troubleshooting a Low Band Problem
- Quick Check to Verify High Band RF Path
- Troubleshooting a High Band Problem
- A10 Input Attenuator B
- A13 RF Front End Assembly (Options 544, 550)
- A15 Front End Control Description
- A15 Front End Control Assembly Troubleshooting
- Verifying Input Attenuator A, Input Attenuator B, Low Band Switch Logic and Power Supplies
- Preselector Tune Output
- Verifying SW3 (Option LNP only)
- Verifying Microwave Preselector Bypass Switch (Option MPB)
- Oscilloscope Test
- A2 Analog IF Assembly Description
- A2 Analog IF Assembly Theory of Operation
- A2 Analog IF Troubleshooting
- Verifying the 22.5 MHz Output Power
- Verifying the 300 MHz LO Input Power from the A16 Reference Assembly
- A3 Digital IF Assembly Description
- A3 Digital IF Assembly Theory of Operation
- A3 Digital IF Troubleshooting
- Verifying the 250 MHz IF Input Power (Option B40 only)
- Verifying the 100 MHz Reference Input
- A14 LO Synthesizer Assembly Description
- A14 LO Synthesizer Theory of Operation
- Manual Selection of Single versus Dual Loop Operation
- Brief Description of the Major Blocks
- A14 LO Synthesizer and A20 YTO Troubleshooting
- Verifying the 4800 MHz 1st LO Reference Power and Frequency Stability
- Verifying the 100 MHz LO Synth Reference Power and Frequency Stability
- Verifying the 1st LO Power and Frequency
- A16 Reference Assembly Description
- A16 Reference Assembly Troubleshooting
- Diagnostic LEDs
- A4 CPU Description
- Rear Panel Connectivity
- A4 Processor Board Assembly Troubleshooting
- BIOS Settings
- A5 Disk Drive
- Overview
- Troubleshooting software related issues
- Reloading the X-Series Software
- Disk Drive Recovery Process
- Replacing the instrument disk drive
- A6 Power Supply Description
- Power Supply Theory of Operation
- A6 Power Supply Assembly Troubleshooting
- Control Inputs
- A7 Midplane Board Assembly Description
- Midplane Board Connections
- A7 Midplane Board Assembly Troubleshooting
- A8 Motherboard Description
- A8 Motherboard Troubleshooting
- A1 Front Panel Assembly
- A25 Wideband Analog IF Troubleshooting - Option B1X and B85
- A25 Wideband Analog IF Assembly Theory of Operation - Option B1X and B85
- A25 Wideband Troubleshooting - Option B1X and B85
- A26 Wideband Digital IF Troubleshooting - Option B1X and B85
- A25 Wideband Analog IF Troubleshooting - Option B2X and B5X
- A25 Wideband Analog IF Assembly Theory of Operation - Option B2X and B5X
- A25 Wideband Analog IF Assembly Troubleshooting - Option B2X and B5X
- A26 Wideband Digital IF Troubleshooting - Option B2X and B5X
- Option BBA Analog I/Q Baseband Inputs Description
- A19 BBIQ Main Board
- Option RTS, Streaming
- Functionality Check
- Block Diagrams
- Analog IF Block Diagram
- Digital IF Block Diagram
- PXA Computer Block Diagram
- Secure service access
- Menus
- Service Key Descriptions
- Corrections
- Band Lock
- LO Band Lock
- Low Noise Path
- Align
- How to Order Parts
- Replaceable Parts
- Hardware
- Before Starting
- Tools you will need
- Major Assembly Locations
- Instrument Outer Case
- Replacement
- Top Brace and Power Supply Bracket
- RF Area (Options 503, 508, 513, 526)
- Attenuators
- Low Band Switch
- YTF Preselector
- Options MPB and LNP
- RF Area (Options 544, 550)
- RF Front End Assembly
- Front End Control Assembly
- LO Synthesizer Assembly
- Reference Assembly
- Option B1X
- Option BBA
- Midplane Board Assembly
- Midplane Board Replacement
- Rear Panel
- Power Supply Assembly
- CPU Assembly
- Disk Drive
- Disk Drive Interconnect
- AIF/DIF Assembly
- Separate AIF/DIF Assembly
- Wideband Extension Board (Option RTS)
- Motherboard Assembly
- Fan Assembly
- Input Connector Assembly
- Front Frame Assembly
- Front Frame Assembly Components
- Post-Repair Procedures
- Additional Tasks
- Performance Verification
- Before Performing a Functional Test
- Test Equipment
- Displayed Average Noise Level (DANL)
- Frequency Readout Accuracy
- Procedure
- Second Harmonic Distortion (SHD)
- Amplitude Accuracy at 50 MHz
- Testing Preamp Option (P03, P08, P13, P26)
- Frequency Response (Flatness)
- Frequency Response (Flatness), Preamp On
- Scale Fidelity
- Instrument Software Overview
- Software Updates
N9030B
Table of contents
manualsdatabase
Your AI-powered manual search engine