Installation Supplement for ACS550-U2 Drives 11Technical DataTechnical DataDimensional DrawingsSee the ACS550-02/U2 User’s Manual for drive module dimensions.Extension Module R73AFE 64626264 30.04.02Dimensions are listed in millimeters and [inches]

General

Introduction

Mounting

Safety

Dimensional Drawings

ABB ACS550-U2 Installation Supplement Manual

ACS550 Series

List of related manuals

Target audience

Contents of the manual

Cybersecurity disclaimer

Drive configuration

Configuring ACS355 drives

Starting ACS355 drives for PROFINET

ACS355 Minimum required parameter settings for PROFINET

ACS355 More parameters written from PLC to drive (optional)

ACS380 Minimum required parameter settings PROFIBUS DS

Starting ACS380 drives for PROFINET

ACS380 More parameters read from drive to PLC (optional)

Configuring ACS550 drives

Starting ACS550 drives for PROFINET

ACS550 More actual values or parameters to be read from drive to PLC (optional)

Configuring ACS580 drives

ACS580 Minimum required parameter settings for PROFIBUS DP

Starting ACS580 drives for PROFINET

ACS580 Minimum required parameter settings for PROFINET

ACS580 More parameters read from drive to PLC (optional)

ACS800 Minimum required parameter settings for PROFIBUS DP

Starting ACS800 drives for PROFINET

ACS800 Minimum required parameter settings for PROFINET

ACS800 More parameters read from drive to PLC (optional)

ACS850 Minimum required parameter settings for PROFIBUS DP

ACS850 Minimum required parameter settings for PROFINET

ACS850 More parameters read from drive to PLC

ACS880 Minimum required parameter settings for PROFIBUS DP

Starting ACS880 drives for PROFINET

ACS880 Minimum required parameter settings for PROFINET

ACS880 More parameters written from PLC to drive (optional)

ACSM1 Minimum required parameter settings for PROFIBUS DP

Starting ACSM1 drives for PROFINET

ACSM1 Minimum required parameter settings for PROFINET

ACSM1 More parameters read from drive to PLC (optional)

SIMATIC Manager

Setting PG/PC interface

Hardware configuration

Adding Rack and CPU to the hardware

Installing GSD files for ABB drives

Adding drives to PROFINET

Downloading Hardware configuration

PLC libraries for S7-300

Symbol Editor

FB500 ABB_DRIVE_CONTROL_FB

Block variables and data types

Setting the drive in standby mode

Setting the drive in run mode

Downloading a program and setting PLC in run mode

VAT table

FC501 ACS_DRIVE_PZD (optional)

Block variable and data types for FC501

Scalable variables and data types

FC500 ACS_DRIVE_PARA (optional)

TIA portal

Configuring S7-300 PLC

Installing GSD and GSDML file for S7-300 PLC

Adding ABB drives to PROFINET

Downloading configuration to PLC

Copying ABB drive libraries to S7-300 project

Adding PLC tags to S7-300

Adding watch and force tables

FC501 ACS_DRIVE_PZD

FC500 ACS_DRIVE_PARA

Error codes for FB500 and FC500

Configuring S7-1200 and S7-1500 PLC

Installing GSD file for S7-1200 PLC

PLC libraries for S7-1200

Downloading configuration to S7-1200 PLC

Copying ABB drive libraries to S7-1200 project

Adding PLC tags to S7-1200

Block variables and data types for FB500

FB501 ACS_DRIVE_PARA

Block variables and data types for FB501

FB502 ACS_DRIVE_PZD

Block variables and data types for FB502

Further information

Contact us

Fieldbus grounding

Drives with embedded fieldbus

Fieldbus modules for ABB drives

ABB cable TK505

AC500 COM1 – Master at the bus line end

AC500‐eCo COM2 – Master at the bus line end

Drive configuration

Starting up ACS310 drives with embedded Modbus RTU

Starting up ACS355 drives with FMBA‐01 Modbus RTU adapter

Starting up ACS800 drives with RMBA‐01 Modbus RTU adapter

Starting up ACS850, ACQ810 drives with embedded Modbus RTU

Starting up ACS880 drives with FSCA‐01 Modbus RTU adapter

Starting up ACSM1 drives with FSCA‐01 Modbus RTU adapter

Install drives library

Control Builder Plus for PLC and Drives

IP configuration of CPU (for Ethernet connection between PC and PLC)

CODESYS

Library Manager

PLC logic

Download program to PLC

Create boot project

Test the program

Read and write more data between PLC and drive (optional)

Visualizations

Add more drives (optional)

Actualization rate

Use of warnings and notes

ACS550 User's Manual

Installation flow chart

Preparing for installation

Installing the drive

Start-up, control with I/O and ID Run

How to start up the drive

How to control the drive through the I/O interface

How to perform the ID Run

About control panels

Assistant Control Panel

Index

Basic Control Panel

Application macros

ABB Standard macro

wire macro

Alternate macro

Motor Potentiometer macro

Hand-Auto macro

PID Control macro

PFC macro

Torque Control macro

Connection example of a two-wire sensor

User parameter sets

Macro default values for parameters

Complete parameter list

Complete parameter descriptions

Embedded fieldbus

Overview

Planning

Communication set-up – EFB

Activate drive control functions – EFB

Feedback from the drive – EFB

Diagnostics – EFB

Modbus protocol technical data

ABB control profiles technical data

Mechanical and electrical installation – FBA

Communication set-up – FBA

Feedback from the drive – FBA

Diagnostics – FBA

ABB Drives profile technical data

Generic profile technical data

Diagnostic displays

Correcting faults

Correcting alarms

Maintenance intervals

Main fan replacement

Internal enclosure fan replacement

Capacitors

Ratings

Input power connections

Motor connections

Brake components

Control connections

Efficiency

Cooling

Dimensions and weights

Degrees of protection

Materials

Applicable standards

UL/CSA markings

Compliance with the IEC/EN 61800-3 (2004)

Liability limits

Product protection in the USA

Product and service inquiries

ACS550-01

ACS550-02

ACS550-U1

ACS550-U2


Contents General Table Of Contents Introduction Mounting Safety Dimensional Drawings	Installation Supplement for ACS550-U2 Drives 11Technical DataTechnical DataDimensional DrawingsSee the ACS550-02/U2 User’s Manual for drive module dimensions.Extension Module R73AFE 64626264 30.04.02Dimensions are listed in millimeters and [inches] Previous Next / 16