Quick Start Reference GuideRefer to Product Safety Manual for Safety StatementsComplete Owner’s Manual available onlineThe switching operation of thismicrowave oven can cause voltagefluctuations on the supply line. Theoperation of this oven under unfavor-able voltage supply conditions canhave adverse effects. This deviceis intended for the connection to apower supply system with a maximumpermissible system impedance Zmax of1.1 Ohm at the interface point ofthe user’s supply. The user has toensure that this device is connectedonly to a power supply system whichfulfills the requirement above. Ifnecessary, the user can ask the publicpower supply company for the systemimpedance at the interface point.So...how do I use it?Manual OperationTo cook food using a specific entered time and power level.1. Press Preheat On/Off pad to start the oven.• Oven Preheating 450°F displays with Oven Preheating flashing.(example of 450°F shown)2. Oven reaches preheat temperature.• Signal sounds and Ready 450°F displays. (example of 450°F shown)3. Place food in the oven.4. Press Time Entry pad.• Enter desired cooking time by using numeric keypad.5. Press Temp Entry pad if cooking temperature differs from preheat temperature.• Enter the new temperature.6. Press Power Level pad.• Press numeric key pad for desired level. Press numeric key pad again toset power level to 100%.• For a lower microwave power, press pads 1 (for 10%) through 9 (for 90%).0 turns off the microwave power and cooking is by convection only.7. If stage cooking is desired, press STAGE pad and repeat steps 3, 4, and 5.• Up to 4 different stages can be programmed.8. Press the Start pad to begin the cooking cycle.Programming Items1. Oven must be ON.• Press Preheat On/Off.• Oven Preheating 450°F displays with Oven Preheating flashing. (exampleof 450°F shown)2. Oven reaches preheat temperature.• Signal sounds and Ready 450°F displays with Ready flashing.(example of 450°F shown)3. Press Program Save pad.4. Press pad to be programmed or reprogrammed.5. Press Time Entry pad to program amount of cooking time.• The total microwave cooking time (all stages combined) is 20 minutes.6. Press Temp Entry pad to program the cooking temperature.• Enter desired temperature by using numeric pads.7. Press Power Level pad to program level of microwave power.• Press numeric key pad for desired level. Press numeric key pad again toset power level to 100%.• For a lower microwave power, press pads 1 (for 10%) through 9 (for 90%).0 turns off the microwave power and cooking is by convection only.8. Press Stage pad.• Enter cook time, temp and power level as in steps 4. 5 and 6.• To enter another cooking stage for that pad, press Stage pad again. Up tofour different stages can be programmed.9. Press the Program Save pad to save the program and changes.NOTE: To discard changes, press Stop/Reset pad before pressing ProgramSave pad.ProgrammingPreheat SettingThe factory default preheat settingis 450°F (230°C). To program thepreheat setting oven must be ON:1. Press Program Save pad.2. Press Temp Entry pad.3. Enter desired temperature by usingthe numeric key pads.4. Preheat temperature is changed.Oven Wall ClearancesA—For North American (UL/CSA) models, allow at least 2” (5.1 cm) of clearance around top of oven.For International (50 Hz) models, allow at least 7” (17,8 cm) of clearance around top of oven.Proper air flow around oven cools electrical components. With restricted air flow, oven may notoperate properly and life of electrical parts is reduced.B—Allow at least 2 9/16” (6,5 cm) between air discharge on back of oven and back wall.C—Allow at least 1 1/4” (3 cm) of clearance around sides of oven.PreprogrammedPadsTo cook food usingpreprogrammed cooking sequences.1. Open oven door and place foodin oven. Close door.2. Press desired pad.3. Oven begins to cook.4. At end of cooking cycle oven beepsand shuts off.No popcornON/OFF TIME ENTRY POWER LEVEL STAGE PROGRAM SAVETEMP ENTRY