Refer to Product Safety Manual for Safety StatementsComplete Owner’s Manual available onlineManual OperationTo cook food using a specific entered time and power level.1. Open oven door and place food in oven. Close door.2. Press TIME ENTRY pad and enter cooking time.3. Press POWER LEVEL pad to program level of microwave power if desired.• For a lower microwave power, press pads 1 (for 10%),through 9 (for 90%), or 0 for no microwave energy.NOTE: Press POWER LEVEL pad once to return to 100% microwavepower.4. Press START pad.5. At end of cooking cycle oven beeps and shuts off.Programming Items1. Open oven door.2. Press and hold pad 1 for approximately 5 seconds.3. Press pad to be reprogrammed.4. Enter cooking time by using the number pads.5. Press POWER LEVEL pad to program level of microwave power if desired.• For a lower microwave power, press pads 1 (for 10%),through 9 (for 90%), or 0 for no microwave energy.NOTE: Press POWER LEVEL pad once to return to 100% microwavepower.6. Press TIME ENTRY pad to add up to four additional cooking stages.• Total cooking time cannot exceed 60 minutes.• Enter cook time and power level as in steps 4 and 5.7. Press START pad to set new programming changes to the pad.NOTE: To discard changes, press STOP/RESET pad or close oven door.Quick Start Reference GuideSo...how do I use it?PreprogrammedPadsTo cook food usingpreprogrammed cooking sequences.1. Open oven door and placefood in oven. Close door.2. Press desired pad.3. Oven begins to cook.4. At end of cooking cycle ovenbeeps and shuts off.The switching operation of this microwave oven can cause voltage fluctuations on the supply line. The operation of this oven under unfavorable voltage supplyconditions can have adverse effects. This device is intended for the connection to a power supply system with a maximum permissable system impedanceZmax of 0.31 Ohms at the interface point of the user’s supply. The user has to ensure that this device is connected only to a power supply system which fulfillsthe requirement above. If necessary, the user can ask the public power supply company for the system impedance at the interface point.X2 Programming(some models)To change the cooking factor:1. Open oven door.2. Press and hold pad 1 forapproximately 5 seconds.3. Press pad to be reprogrammed.4. Press the X2 pad.5. Press a numbered pad tochange the cooking factor.• Cooking factor can be set from10% to 100%.• Default is 80%.• Pad 5 would change thecooking factor to 50%.6. Press START pad to savechanges.X2 Pad (some models)1. Open oven door and place food in oven. Close door.2. Press X2 pad.3. Press desired preprogrammed pad or pad sequence.4. Oven begins cooking. Displayed cooking time is the total of originalcooking time and added X2 time.2CLEAN FILTERThis oven displays CLEAN FILTERat user defined intervals. When themessage displays ACP recommendscleaning the air filter thoroughly.Cleaning the air filter will not shutoff the message. The message willstop displaying automatically after24 hours. Depending on microwaveuse and environmental conditions,the filter may need to be cleanedmore frequently. Once the frequencyis determined, set the option for theappropriate time frame.Oven ClearancesA—For North American (UL/CSA) models, allow atleast 7” (17.8 cm) of clearance around top of oven.For International (50 Hz) models, allow at least 7”(17.8 cm) of clearance around top of oven. Properair flow around oven cools electrical components.With restricted air flow, oven may not operateproperly and life of electrical parts is reduced.B—Allow at least 2 9/16” (6.5 cm) between airdischarge on back of oven and back wall.C—Allow at least 7” (17.8 cm) around sides of oven.Time EntryPower Level StartStop/Reset