ADTRAN DDS-DP Installation And Maintenance Manual

Contents

ADTRAN DDS-DP Installation And Maintenance Manual Manual pdf 1 page image

161433105L2-5D Section 61433105L2, Issue 41. GENERALThis practice provides installation and maintenanceprocedures for the ADTRAN Series 5 Total Reach ®DDS-DP All-Rate DDS Dataport. Figure 1 is anillustration of the ADTRAN Series 5 Total ReachDDS-DP (P/N 1433105L5).Revision HistoryThis is the initial release of this document. Futurerevisions will be described in this subsection.Features• 2-wire deployment• Repeaterless operation• Bridged tap tolerant• Span power for remote Total Reach DDS-Rtermination unit• Utilization in SLC Series 5 and Series 2000 channelbanksSeries 5 Total Reach DDS-DPTotal Reach All-Rate DDS DataportInstallation and MaintenanceSection 61433105L2-5DIssue 4, June 2000CLEI Code # 5SC531PF_ _Trademarks: Any brand names and product names included in this document are trademarks,registered trademarks, or trade names of their respective holders.• Loop Quality Monitor and A/B signaling options• Bidirectional DS0 loopback capability• Transmits Mux Out of Sync code upstream duringout of service loop condition.• Embedded Digital System 6 capabilities for remoteprovisioning, and performance monitoring.DescriptionThe ADTRAN Series 5 Total Reach DDS-DP is afunctional replacement for the SLC® Series 5 OCU DP,CLEI 5SCU48, delivering data at rates up to 64 kbpsusing a single copper pair. Used in combination with theTotal Reach DDS-R termination unit, the Series 5 TotalReach DDS-DP can accommodate extended looplengths, eliminating the need for DDS repeaters. TheSeries 5 Total Reach DDS-DP span powers the TotalReach DDS-R located at the customer premises. TheTotal Reach DDS-R converts the 2-wire signal to thetraditional 4-wire Alternate Mark Inversion (AMI) signalfor presentation to the customer.The ADTRAN Series 5 Total Reach DDS-DPoccupies a single channel position in the AT&T® SLCSeries 5 and Series 2000 or Series 5 compatiblechannel bank. It provides the interface between a DS0timeslot of the T-carrier data stream and the 2-wiremetallic loop extending to the customer premises. TheFigure 1. Series 5 Total Reach DDS-DPCONTENTS1. GENERAL ...................................................................... 12. INSTALLATION ........................................................... 33. TESTING ........................................................................ 34. REMOTE PROVISIONING AND DIAGNOSTICS ..... 55. DEPLOYMENT GUIDELINES .................................... 66. MAINTENANCE ........................................................... 77. WARRANTY AND CUSTOMER SERVICE ............... 8FiguresFigure 1. Series 5 Total Reach DDS-DP ........................... 1Figure 2. Total Reach DDS Circuit Diagram .................... 2Figure 3. Option Switch ..................................................... 2Figure 4. DS0 Bidirectional Loopback .............................. 4Figure 5. DDS Trouble Codes ........................................... 5Figure 6. Remote End Initiated Loopback, Local Loop .... 6Figure 7. Remote End Initiated Loopback, CustomerLoop .................................................................... 6TablesTable 1. Option Settings..................................................... 2Table 2. LED Indication ..................................................... 4Table 3. Latching Loopback Activation Sequence ............ 5Table 4. Alternating Loopback Activation Sequence ........ 5Table 5. Cable Type and Temperature Loss Data @13.3 kHz ............................................................... 7Table 6. Total Reach DDS Insertion LossMeasurements ...................................................... 7Table 7. Compliance codes ................................................ 71433105SYNCSXFECRCNEDSUQMLBKMANSW2DDS-DP