NetVanta ISDN BRI Dial Backup Interface Module (DIM) P/N 1200865L1For more detailed documentation, visit us online at www.adtran.com.Quick Start Guide®Quick Start Guide, 61200865L1-13E, July 2006 Technical Support 1-888-4ADTRAN (1-888-423-8726) Copyright © 2006 ADTRAN, All Rights ReservedISDN BRI DIM C OMMANDSalias <“text”>Populates the ifAlias OID (Interface Table MIB of RFC2863) for all physical and virtualinterfaces when using SNMP management station.bonding txadd-timer Specifies the value (in seconds) for the aggregate call connect timeout. Use the noform of this command to return to the default value. Specifies the number of seconds the endpoint will wait foradditional channels (to add to the bonded aggregate) beforeconsidering the bonding negotiation a failurebonding txcid-timer Specifies the value (in seconds) for the bearer channel (B-channel) negotiationtimeout. Use the no form of this command to return to the default value. Specifies the number of seconds the endpoint allots fornegotiating data rates and channel capacities beforeconsidering the bonding negotiation a failure.bonding txdeq-timer Specifies the value (in seconds) for the network delay equalization timeout. Use the noform of this command to return to the default value. Specifies the number of seconds the endpoint allots forattempting to equalize the network delay between bearerchannels before considering the bonding negotiation a failure.bonding txfa-timer Specifies the value (in seconds) for the frame pattern detection timeout. Use the noform of this command to return to the default value. Specifies the number of seconds the endpoint allots forattempting to detect the bonding frame pattern (when a call isconnected) before considering the bonding negotiation afailure.bonding txinit-timer Specifies the value (in seconds) for the originating endpoint negotiation timeout. Usethe no form of this command to return to the default value. Specifies the number of seconds the endpoint waits to detectthe bonding negotiation frame pattern from the remoteendpoint (when a call is connected) before considering thebonding negotiation a failure.bonding txnull-timer Specifies the value (in seconds) for the answering endpoint negotiation timeout. Usethe no form of this command to return to the default value. Specifies the number of seconds the endpoint waits to detectthe bonding negotiation frame pattern from the originatingendpoint (after answering a call) before considering thebonding negotiation a failure.caller-id override [always | if-no-CID ]Configures the unit to replace caller ID information with a user-specified number. Usethe no form of this command to disable any caller ID overrides.always Always forces replacement of the incoming caller ID numberwith the number given.if-no-CID Replaces the incoming caller ID number with the number givenonly if there is no caller ID information available for theincoming call.description Identifies the specified interface, both physical and virtual (for example, circuit ID,contact information, etc.), using up to 80 alphanumeric characters.isdn spid1 Specifies the Service Profile Identifiers (SPIDs). This information should be suppliedby your service provider. Use the no form of this command to remove a configuredSPID.<spid> Specifies the 8 to 14 digit number identifying your Basic RateISDN (BRI) line in the central office switch. A SPID is generallycreated using the area code and phone number associatedwith the line and a four-digit suffix.<ldn> Optional. Specifies the LDN assigned to the circuit by theservice provider. The LDN is the number used by remotecallers to dial into the ISDN circuit. If the > field is leftblank, the AOS will not accept inbound dial-backup calls to theBRI module.isdn spid2 See isdn spid1.isdn switch-type [basic-5ess | basic-dms | basic-net3 | basic-ni*]Specifies the ISDN signaling type configured on the Basic Rate ISDN (BRI) interface.The type of ISDN signaling implemented on the BRI interface does not always matchthe manufacturer of the Central Office switch. Use the no form of this command toreturn to the default value. This setting is determined by your service provider.basic-5ess Specifies Lucent/AT&T 5ESS signaling.basic-dms Specifies Nortel DMS-100 custom signaling.The basic-dmssignaling type is not compatible with proprietary SL-1 DMSsignaling.basic-net3 Specifies Net3 Euro-ISDN signalling.basic-ni* Specifies National-ISDN 1 signaling.shutdownDisables the interface (both physical and virtual) so that no data will be passedthrough. Use the no version of this command to turn on the interface and allows it topass data.*Indicates default values.
