Contents - Declaration of conformity
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Quickstart guide
- Safety information
- Power supply
- Wireless operation
- Device overview
- International key assignment
- Device rear (mounting plate)
- Introduction
- Mounting/Installation
- Fixing the mounting plate to the wall
- Connecting the components
- Installing the micro SD card
- Commissioning
- For a system that is already installed
- Logging out from the wireless alarm system
- Configuration
- Menu control elements
- Login screen
- Main menu
- INFO
- Communication
- PSTN
- Ethernet
- Mobile
- Customisation
- Status
- Components
- Detectors
- Wireless Zones
- Wired Zones
- Wireless control panel
- External Sirens
- Wired Sirens
- Indoor sounder
- Info module/indoor siren
- WUM (Wireless Universal Module)
- Door locks
- RF repeater
- Outputs
- Radio Outputs
- Wired Outputs
- Combination outputs
- Partitions
- Configure partitions
- System
- General
- Installer details
- User access
- User Reset
- Confirmation
- Hardware
- Security settings
- Panel upgrade
- Checking for an upgrade
- Backup/restore
- Report
- Network setup
- IP Mobile Setup
- Email setup
- VoIP dialler setup
- ARC reporting
- ARC Reporting, Phone Book
- ARC Reporting, Account Numbers
- ARC Reporting, Fast Fmt Channels (for "Fast Format" protocol only)
- ARC Reporting, CID/SIA Triggers (for all protocols EXCEPT "Fast Format")
- Encryption
- ARC Reporting, More
- Nursing emergency call
- Social Care, Phone Book
- Social Care, Account Numbers
- Voice dialler
- Speech Dialler, Triggers
- Speech Dialler, Destinations
- Speech Dialler, Test Call
- SMS, Triggers
- SMS, Destinations
- SMS, Destinations, Message X
- SMS, Destinations, Message, Telephone Recipients
- SMS, Messages
- SMS, PSTN SMS
- SMS, test call
- Email
- Email, Triggers
- Email, Destinations
- Email, Messages
- Email, test call
- Communication options
- Contacts
- Test
- Virtual keypad
- Appendix
- Compatible equipment
- Default values/factory defaults
- User menu
- Start Wizard
- Repairs and maintenance
- S/W upgrade
- Software upgrade with new files from the FTP server
- ARC/ESCC reporting
- CID/SIA Events
- Email error messages
- TCP/IP error messages
- VoIP error messages
- Log book entries
- User numbers
- Troubleshooting
- Carry out a GSM/wireless mobile manual test call, prepaid
- Trace, recording communication sequences
- Router, IAD, Firewall
- Time zones
- GSM network notification centre
- Email notification/email setup
- IP Mobile Setup / Mobile Data Communication
- Index
- Linker Kreuthweg
|
Appendix269S/W upgradeNoteSW >=3.00.03There are two ways to perform a software upgrade. Software upgrade with new files that are saved on the PC. Software upgrade with new files that are stored on the FTP server.Software upgrade with new files on the PCImportantSaving and restoring the configurationAs part of a comprehensive update, the Secvest wireless alarm system is reset to the factory defaults.It is therefore essential to save the alarm control panel configuration in advance:1st "Installer Mode" web server2. "System"3rd "Backup/restore"4. "Backup"After completing the update, the configuration (inc. all component IDs) can be restored:5. "Installer Mode" web server6. "System"7. "Backup/restore"8. "Load Configuration"ImportantSW >= 3.00.06, saving and restoring the configurationBefore the alarm panel starts the upgrade, the configuration files and the SSL certificate are saved automatically onthe internal flash drive. The new software is then installed, and the alarm panel restarted. At this point, the factory set-tings are used first, but the alarm panel then automatically reproduces the configuration files and the SSL certificatefrom the flash drive (as if the configuration had been saved/reproduced manually). This means that the Start Wizard isnot used, the SSL certificate is not regenerated and, more importantly, that the installer does not have to go to the sitein order to respond to the command prompt of the Start Wizard.ImportantChanges have been made to the following menus as part of S/W 2.00.00 VoIP Dialler Setup Contacts -> SIP User ID Outputs -> Type "User defined" ARC/ESCC reporting -> IP portPlease check these menus after carrying out the configuration and adjust the settings accordingly.
|
