Contents - Declaration of conformity
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Quickstart guide
- Safety information
- Power supply
- Wireless operation
- Device overview
- International key assignment
- Device rear (mounting plate)
- Introduction
- Mounting/Installation
- Fixing the mounting plate to the wall
- Connecting the components
- Installing the micro SD card
- Commissioning
- For a system that is already installed
- Logging out from the wireless alarm system
- Configuration
- Menu control elements
- Login screen
- Main menu
- INFO
- Communication
- PSTN
- Ethernet
- Mobile
- Customisation
- Status
- Components
- Detectors
- Wireless Zones
- Wired Zones
- Wireless control panel
- External Sirens
- Wired Sirens
- Indoor sounder
- Info module/indoor siren
- WUM (Wireless Universal Module)
- Door locks
- RF repeater
- Outputs
- Radio Outputs
- Wired Outputs
- Combination outputs
- Partitions
- Configure partitions
- System
- General
- Installer details
- User access
- User Reset
- Confirmation
- Hardware
- Security settings
- Panel upgrade
- Checking for an upgrade
- Backup/restore
- Report
- Network setup
- IP Mobile Setup
- Email setup
- VoIP dialler setup
- ARC reporting
- ARC Reporting, Phone Book
- ARC Reporting, Account Numbers
- ARC Reporting, Fast Fmt Channels (for "Fast Format" protocol only)
- ARC Reporting, CID/SIA Triggers (for all protocols EXCEPT "Fast Format")
- Encryption
- ARC Reporting, More
- Nursing emergency call
- Social Care, Phone Book
- Social Care, Account Numbers
- Voice dialler
- Speech Dialler, Triggers
- Speech Dialler, Destinations
- Speech Dialler, Test Call
- SMS, Triggers
- SMS, Destinations
- SMS, Destinations, Message X
- SMS, Destinations, Message, Telephone Recipients
- SMS, Messages
- SMS, PSTN SMS
- SMS, test call
- Email
- Email, Triggers
- Email, Destinations
- Email, Messages
- Email, test call
- Communication options
- Contacts
- Test
- Virtual keypad
- Appendix
- Compatible equipment
- Default values/factory defaults
- User menu
- Start Wizard
- Repairs and maintenance
- S/W upgrade
- Software upgrade with new files from the FTP server
- ARC/ESCC reporting
- CID/SIA Events
- Email error messages
- TCP/IP error messages
- VoIP error messages
- Log book entries
- User numbers
- Troubleshooting
- Carry out a GSM/wireless mobile manual test call, prepaid
- Trace, recording communication sequences
- Router, IAD, Firewall
- Time zones
- GSM network notification centre
- Email notification/email setup
- IP Mobile Setup / Mobile Data Communication
- Index
- Linker Kreuthweg
|
Quickstart guide7Quickstart guideTarget audienceThe instructions for installers aim to help navigate the in-dividual menus of the program interface.These instructions are aimed at trained technicians thathave taken an ABUS Security-Center GmbH & Co. KGseminar and acquired the necessary fundamentalknowledge about the following: Installing the wireless alarm system. Installing peripheral devices for the wireless alarmsystem (e.g. detectors, sirens, GSM/GPRS module,surveillance cameras). Configuring peripheral devices for the wireless alarmsystemThese instructions for installers provide an overview ofthe setting options in the individual menus.Installing SecvestThe installation of the Secvest wireless alarm system isdescribed in chapter Mounting/Installation from page 24.Additional information can be found in the document sup-plied in the scope of delivery, "Quick Guide FUAA50000".The installation/user manual can also be downloaded asa PDF document.Link to download the document:www.abus.com/ger/products/FUAA50000Configuring SecvestThe configuration of the wireless alarm system is de-scribed in chapter Configuration from page 31.Secvest function testAfter installation and configuration, perform a completefunction test for all systems and components.Train the user in the basic operation of the system: Logging in/out Arming/disarming the system Operating the Secvest and remote control. Create a handover logNoteFollow the instructions in user training in the ap-pendix.
|
