Accusplit AE1720WPR Series Instructions Manual

DISPLAY MODES• STEP: STEP mode showsyour step count since last reset,up to 1,000,000 steps.• ◯: ACTIVITY TIMERMODE shows total activitytime in minutes and secondssince last reset. The timer runsautomatically whenever stepsare being recorded.Adjusting your Pedometer’sMeasurement Sensitivity AE1700pedometers are highly accurate stepcounters. However, some walkers mayfind that their step counts tend to bea bit too high, or too low. All AE1700models come with a sensitivity adjust-ment, to help account for individualdifferences. The adjustment switch hasthree positions: “+,” “-,” and center.The adjustment switch is located on thebottom of the pedometer, on the right-hand side when looking from the front.Adjustment Procedure: Take 100 steps,then check STEPS display to see howmany steps were actually counted.Repeat once to make sure results areabout the same. If the pedometer countsfewer steps than you actually walked,slide the sensitivity adjustment towardsthe “+” icon. This will increase recordedsteps by about 10%. If the pedometercounts more steps than you actuallywalked, slide the sensitivity adjustmenttowards the “-” icon. This will decreaserecorded steps by about 10%.WEARING YOUR PEDOMETERWhile gently holding the belt clip open,slide the pedometer onto your belt or thetop edge of your pants or skirt. It shouldfit snugly and level, above one knee.Note: The pedometer should be asvertical as possible. Walkers with largerstomachs may find it helpful to wear thepedometer farther back on the body,toward one hip. The cover must be closedfor the pedometer to work. To avoidlosing or dropping your pedometer, usethe included leash and clip to fasten thepedometer securely to your clothing.Attaching the Leash: Attach thepedometer to the leash by looping theleash through the pedometer leash slot.Next, loop the leash through the metalclip. Finally, clasp the waistband of yourclothing with the metal clip. You can alsouse a safety pin to fasten the leash toyour clothing, loop the leash through yourbelt or belt loop, or use a badge holder.ACCUSPLIT AE1720WPR Series PedometerINSTRUCTIONSACCUSPLIT, Inc. • 2290M Ringwood Ave. • San Jose, CA 95131800-965-2008 • 925-226-0888 • FAX 925-463-0147 • www.ACCUSPLIT.com • support@ACCUSPLIT.comEat Right! Walk More! Live Well!The ACCUSPLIT LifestyleCongratulations on taking the first step to wellnesswith your purchase of an ACCUSPLIT pedometer.It’s easy to set up your new pedometer.Just follow the steps below, and start walking! Red:MODE9789ACCUSPLIT EAGLE�STEP▶White:RESET970-071First, loop thepedometer leash slotNext, loop the metalclip, then clasp clothingOr, loop abadge holder,then put into pocket(Badge holdernot included)Or, loop a belt or belt loopVIEWING YOUR RESULTSOnce you put on your pedometer with thecover closed, it will automatically beginto record your steps, and activity time.Repeatedly press the red MODE button tocycle through the pedometer modes:STEP → ACTIVITY TIMER → STEPRESETTING YOUR PEDOMETERMost people prefer to reset step countsdaily. To reset: press and hold the whiteRESET button for at least 2 seconds.REPLACING THE BATTERYWhen the display starts to dim or goesblank, it is time to replace the battery.Your pedometer uses one Type L1142(LR43) 1.5 volt silver oxide battery.To replace:1. Insert a coin into the slot on the frontof the case, and twist counterclock-wise to loosen the battery door.2. Remove battery door and take out theold battery. Replace it with a newbattery. The battery’s positive (+)terminal should be FACE UP while youput it into the pedometer.3. Put the battery door back on and twistthe coin clockwise to tighten.You are also helping to support the cause of breast cancerawareness and research. A portion of the proceeds from yourpurchase will be donated to a breast cancer initiative.

/ 1

Related manuals for Accusplit AE1720WPR Series