Canon D1300 Series Service Manual

88 8-158-15Service Mode > COPIER > FUNCTION > SPLMANService Mode > COPIER > FUNCTION > SPLMAN■ SYSTEMCOPIER > FUNCTION > SYSTEMPANEL-UP Download from USB memory (PANEL)Details To perform downloading when PANEL exists in the root directory of theUSB memory.Use case At upgradeAdj/set/operate method 1) Install the USB memory.2) Select the item, and then press OK key.3) Turn OFF/ON the main power switch.Caution Do not turn OFF/ON the power before “Executing...” disappears.Related service mode COPIER> FUNCTION> SYSTEM> DOWNLOAD, BKUP-UPBKUP-UP Download from USB memory (BKUP)Details To perform downloading when BKUP exists in the root directory of theUSB memory.Use case At upgradeAdj/set/operate method 1) Install the USB memory.2) Select the item, and then press OK key.3) Turn OFF/ON the main power switch.Caution Do not turn OFF/ON the power before “Executing...” disappears.Related service mode COPIER> FUNCTION> SYSTEM> PANEL-UPLOGWRITE Writing sublog to USB memoryDetails To write sublog that includes the following information to the USBmemory.• Job list (job names, user names, and destinations)• Communications log (destinations and user names)• Job log (user names and job names)Use case When analyzing the cause of a problemAdj/set/operate method 1) Install the USB memory.2) Select the item, and then press OK key.3) Turn OFF/ON the main power switch.Caution Do not turn OFF/ON the power before “Executing...” disappears.IMPORT Reading of service mode setting value from USB memoryDetails To write the service mode setting values (excluding those related toReader/ADF) to the USB memory.Use case When replacing the Main Controller PCB as a measure against failuresAdj/set/operate method 1) Install the USB memory.2) Select the item, and then press OK key.3) Turn OFF/ON the main power switch.Caution Do not turn OFF/ON the power before “Executing...” disappears.EXPORT Writing service mode setting value to USB memoryDetails To write the service mode setting values (excluding those related toReader/ADF) to the USB memory.Use case When replacing the Main Controller PCB as a measure against failuresAdj/set/operate method 1) Install the USB memory.2) Select the item, and then press OK key.Caution “Executing...” disappears when writing is completed.T-8-13■ SPLMANCOPIER > FUNCTION > SPLMANSPL14159 Fixing of USB device IDDetails To fix the USB device ID to “000000000000”.Driver for each machine is installed to a PC. However, by fixing theserial number, the PC considers that any connected machine to bethe same machine; thus, there will be no need to install the driversmany times.Adj/set/operate method 1) Enter the value, and then press OK key.2) Turn OFF/ON the main power switch.Display/adj/set range 0 to 10: OFF, 1: ONDefault value 0SPL65677 Increase of paper leading edge marginDetails To increase the margin on the leading edge of paper.As the value is incremented by 1, the margin is increased by 0.1 mm.If the setting is incompatible with SPL68676 (decrease of margin), thesetting is disabled (the margin will be standard).Adj/set/operate method 1) Enter the setting value, and then press OK key.2) Turn OFF/ON the main power switch.Display/adj/set range 0 to 20Unit 0.1 mmDefault value 0Related service mode COPIER> FUNCTION> SPLMAN> SPL68676SPL68676 Decrease of paper leading edge marginDetails To decrease the margin on the leading edge of paper.As the value is incremented by 1, the margin is decreased by 0.1 mm.If the setting is incompatible with SPL65677(increase of margin), thesetting is disabled (the margin will be standard).Adj/set/operate method 1) Enter the setting value, and then press OK key.2) Turn OFF/ON the main power switch.Display/adj/set range 0 to 20Unit 0.1 mmDefault value 0Related service mode COPIER> FUNCTION> SPLMAN> SPL65677SPL68677 Increase of paper right and left marginsDetails To increase the margins on the right and left edges of paper.As the value is incremented by 1, the margin is increased by 0.1 mm.If the setting is incompatible with SPL25607 (decrease of margins),the setting is disabled (the margins will be standard).Adj/set/operate method 1) Enter the setting value, and then press OK key.2) Turn OFF/ON the main power switch.Display/adj/set range 0 to 20Unit 0.1 mmDefault value 0Related service mode COPIER> FUNCTION> SPLMAN> SPL25607