Carrier 50HX024-060 Product Data

Also see for 50HX024: Installation, start-up, and operating instructions

Contents

Electrical data (cont)50HX ELECTRIC HEATER PACKAGES — 208/240 V, SINGLE-PHASE,SINGLE-POINT WIRING CONNECTIONSUNITSIZE50HXELECTRIC HEATACCESSORY KITCPHEATER---A00ELECTRIC HEAT(kW)*HEATERFLAMIN CIRCUITAMPACITY FORWIRE SIZINGMAX FUSEOR HACRBRKR MOCP208 V 240 V 208 V 240 V 208 V 240 V 208 V 240 V 208 V 240 V024001 3.75 5.0 18.1 20.8 42.1 45.6 50 50 — —002 5.60 7.5 27.1 31.3 53.4 58.6 60 60 — —015 7.50 10.0 36.1 41.7 64.7 71.6 — — 70 80030001 3.75 5.0 18.1 20.8 45.3 48.8 50 50 — —014 5.60 7.5 27.1 31.3 56.6 61.8 60 — — 70015 7.50 10.0 36.1 41.7 67.9 74.8 — — 70 80016 11.30 15.0 54.1 62.0 90.4 100.3 — — 100 110036001 3.75 5.0 18.1 20.8 48.3 51.7 60 60 — —014 5.60 7.5 27.1 31.3 59.5 64.8 60 — — 70015 7.50 10.0 36.1 41.7 70.8 77.8 — — 80 80016 11.30 15.0 54.3 62.0 93.3 103.2 — — 100 110017 15.00 20.0 72.2 83.3 116.0 129.9 — — 125 150042001 3.75 5.0 18.1 20.8 52.1 55.5 60 60 — —014 5.60 7.5 27.1 31.3 63.3 68.6 — — 70 80015 7.50 10.0 36.1 41.7 74.6 81.6 — — 80 90016 11.30 15.0 54.1 62.0 97.1 107.0 — — 100 110017 15.00 20.0 72.2 83.3 119.8 133.7 — — 125 150048013 3.75 5.0 18.1 20.8 64.2 67.6 — — 80 80014 5.60 7.5 27.1 31.3 75.4 80.7 — — 90 90015 7.50 10.0 36.1 41.7 86.7 93.7 — — 100 100016 11.30 15.0 54.1 62.0 109.2 119.1 — — 110 125017 15.00 20.0 72.2 83.3 131.9 145.8 — — 150 150060013 3.75 5.0 18.1 20.8 72.0 75.5 — — 90 100014 5.60 7.5 27.1 31.3 83.3 88.5 — — 100 100015 7.50 10.0 36.1 41.7 94.6 101.5 — — 100 110016 11.30 15.0 54.1 62.0 117.1 126.9 — — 125 150017 15.00 20.0 72.2 83.3 139.6 153.5 — — 150 175LEGENDFLA — Full Load AmpsHACR BRKR — Heating, Air Conditioning and Refrigeration CircuitBreakerMOCP — Maximum Overcurrent Protection (fuses or HACR-type circuit breaker)NEC — National Electrical Code*Electric heat capacity (kW) is based on heater voltages of 208 v or240 v. If power distribution voltage to units varies from rated heatervoltage, see Wattage Multiplication Factors table on page 19.NOTE: In compliance with NEC requirements for multimotor and com-bination load equipment (refer to NEC Articles 430 and 440), the over-current protective device for the unit shall be fuse or HACR breaker.22