6Assembling the CooktopGrill Compartment Assemblywarningfailure to remove the plastic coating and packing•materials from the appliance before use will result ina fire hazard.to avoid a suffocation hazard, keep all plastic and•packing materials out of reach of children.to avoid the risk of fire, explosion or carbon•monoxide poisoning, do not attempt to use youroutdoor grill without the flame spreaders, grates andburners completely and properly assembled.for proper operation the outdoor grill must be level•during use.Before using the outdoor grill for the first time,1.remove the plastic coating from all of the outsidesurfaces of the outdoor grill. remove any excess gluefrom the surfaces using Dacor Stainless Steel cleaner(included with your outdoor grill).Open the canopy.2.Put the flame spreaders over the top of the burners3.inside the grill compartment. rest them on the lowershelves toward the front and rear. the lighting holesgo toward the bottom. If the outdoor grill is equippedwith a sear burner, put one of the larger flame spread-ers over it.Put the grates over the top of the flame spreaders,4.resting the ends on the upper shelves toward the frontand back of the compartment.Make sure the grates and flame spreaders lie flat and5.that there is nothing beneath them.mount the warming rack on the pins near the top of6.the compartment.Insert the drip tray into the slot below the burners.7.Push it all the way in until it stops.Optional Side Burner AssemblyPlace the burner heads over the burner bases. Line up1.the notches on the side of each burner head with thepins on each burner base.Put the burner caps over the top of the burner heads.2.the notches on the bottom line up with the pins onthe burner base. Gently twist each cap back and forthto make sure it seats completely.Gently set the grate on top of the side burner cook-3.top. Line up the legs with the corresponding dimples.the side burner cover goes over the top of the grateand helps keep the side burner clean when not in use.Setting Up Your Outdoor GrillElectrical RequirementswarningConnect the power cords for this outdoor cooking•gas appliance only to an electrically grounded outletthat meets local codes for outdoor appliances. Inthe absence of local codes, the electrical outletmust meet National electric Code, ANSI/NfPA 70or Canadian electrical Code Standards for outdoorappliances.Keep any electrical supply cords and the fuel supply•hose away from any heated surfaces and sharpedges. Keep the power cords dry and up off of theground.the outdoor grill and the rotisserie motor are•equipped with three prong grounding plugs to mini-mize the possibility of an electric shock hazard fromthis appliance . Plug them only into a three prongelectrical outlet equipped for use with outdoor appli-ances that is protected by a minimum 15 Amp. circuitbreaker or fuse.Dacor highly recommends installing a dedicated•electrical outlet for your outdoor grill according to therequirements above.Electrical Connectionelectrical connection for Built-in installations:Connect the power cord from the outdoor grill to an•electrical outlet that meets the the above require-ments. An outlet equipped with a ground fault inter-rupter (GfI) is highly recommended whether or notit is required by local code. GfI electrical outlets aredesigned to minimize the risk of injury due to an elec-tric shock.electrical connection for dacor cart installations:Dacor OBC series grill carts are designed for a custom fitwith OB and OBS series grills. the OBC series grill cart isequipped with a GfI type electrical outlet.Connect the outdoor grill power cord to the electrical1.outlet located on the back wall at the back of the LPtank compartment.If the cart is equipped with a warming oven, plug it2.into the same electrical outlet.Pull open the cover on the cart power input plug and3.connect an extension cord (15 Amp. minimum).Connect the other end of the extension cord to a4.grounded three prong electrical outlet equipped foruse with outdoor appliances that meets the require-ments above.