Contents - Table Of Contents
- Table Of Contents
- H1 Pumps General Specification
- H1P 115/130 Operating Parameters
- Fluid Specifications
- H1P 115/130 Mounting Flange Loads
- Charge pump
- Electrical Displacement Control (EDC)
- EDC Solenoid Data
- Response Time, EDC 115/130
- Manual Displacement Control (MDC)
- MDC General Information
- Control Response
- Connector
- Forward-Neutral-Reverse Electric Control (FNR)
- Non Feedback Proportional Electric Control (NFPE)
- Automotive Control (AC)
- Performance functions
- Fan Drive Control (FDC)
- Manual Over Ride (MOR)
- Swash Plate Angle Sensor for EDC Controls
- Swash Plate Angle Sensor Connector
- Swash plate angle sensor for NFPE and AC2 controls
- Control-Cut-Off valve (CCO valve)
- CCO solenoid data
- H1P input shaft - Option G3 (SAE D, 13 teeth)
- H1P input shaft - Option G2 (SAE D, 27 teeth)
- H1P input shaft - Option F3, Code 44-3
- Tapered shaft customer acknowledgement
- H1P 115/130 Auxiliary mounting - Option H1 (SAE A, 11 teeth)
- H1P 115/130 Auxiliary mounting - Option H2 (SAE A, 9 teeth)
- H1P 115/130 Auxiliary mounting - Option H3 (SAE B, 13 teeth)
- H1P 115/130 Auxiliary mounting - Option H4 (SAE D, 13 teeth)
- H1P 115/130 Auxiliary mounting - Option H5 (SAE B-B, 15 teeth)
- H1P 115/130 Auxiliary mounting - Option H6 (SAE C, 14 teeth)
- H1P 115/130 Auxiliary mounting - Option S1 (SAE B-B, 14 teeth)
- H1P 115/130 displacement limiter, option B and D
- Port Description H1P115/130
- Dimensions H1P 115/130
- Electric Displacement Control (EDC), option A2 (12 V) / A3 (24 V)
- H1P 115/130 Manual Displacement Control (MDC), option M1
- H1P 115/130 Manual Displacement Control (MDC) with NSS, option M2
- H1P 115/130 Manual Displacement Control (MDC) with CCO, option M3, M4
- H1P 115/130 Manual Displacement Control (MDC) with NSS and CCO, option M5, M6
- Non Feedback Proportional Electric control (NFPE), with manual override, option A8 (12 V) / B8 (24 V)
- Automotive Control (AC) Dimensions
- Forward-Neutral-Reverse (FNR) with manual override, options A9 (12 V) / B1 (24 V)
- H1P 115/130 suction filtration, option L
- H1P 115/130 filtration, option M
| 
Parameter Minimum Typical MaximumSensitivity 70.0 mV/deg 78.0 mV/deg 85.8 mV/degWorking range (swash plate angle) –18° 0° 18°Correlation between signals 1 and 22) 475 mV 500 mV 525 mV1) Up to duration of 2.5 seconds at 25°C2) Signal 1 (nominal) is lower than signal 2 (redundant)Swash Plate Angle Sensor ConnectorDEUTSCH 4-pin connector12344-Pin Legend:1. Ground (GND)2. Output Signal 2 (SIG2) – Secondary (redundant)3. Output Signal 1 (SIG1) – Primary (nominal)4. Supply (V+)Connector order numbersDescription Quantity Order numberMating connector DTM06-4S-E004 1 11105824Wedge lock W4S 1 11084558Socket contact (16-18 AWG) 0462-201-16141 2 K02325Interface with ECUInterface with ECU schematicECUV+Sig1Sig2GndE3 340R 340ROut 2Out 1VCCVCCGndGnd340R340R0.1uF5.6 nF5.6 nFE2E1Minimum recommended load resistance is 100 kΩ.Technical InformationH1P 115/130 Axial Piston Single PumpsControl Options© Danfoss | May 2018 BC00000198en-US0901 | 39 |
