Contents - Table Of Contents
- Table Of Contents
- H1 Pumps General Specification
- H1P 115/130 Operating Parameters
- Fluid Specifications
- H1P 115/130 Mounting Flange Loads
- Charge pump
- Electrical Displacement Control (EDC)
- EDC Solenoid Data
- Response Time, EDC 115/130
- Manual Displacement Control (MDC)
- MDC General Information
- Control Response
- Connector
- Forward-Neutral-Reverse Electric Control (FNR)
- Non Feedback Proportional Electric Control (NFPE)
- Automotive Control (AC)
- Performance functions
- Fan Drive Control (FDC)
- Manual Over Ride (MOR)
- Swash Plate Angle Sensor for EDC Controls
- Swash Plate Angle Sensor Connector
- Swash plate angle sensor for NFPE and AC2 controls
- Control-Cut-Off valve (CCO valve)
- CCO solenoid data
- H1P input shaft - Option G3 (SAE D, 13 teeth)
- H1P input shaft - Option G2 (SAE D, 27 teeth)
- H1P input shaft - Option F3, Code 44-3
- Tapered shaft customer acknowledgement
- H1P 115/130 Auxiliary mounting - Option H1 (SAE A, 11 teeth)
- H1P 115/130 Auxiliary mounting - Option H2 (SAE A, 9 teeth)
- H1P 115/130 Auxiliary mounting - Option H3 (SAE B, 13 teeth)
- H1P 115/130 Auxiliary mounting - Option H4 (SAE D, 13 teeth)
- H1P 115/130 Auxiliary mounting - Option H5 (SAE B-B, 15 teeth)
- H1P 115/130 Auxiliary mounting - Option H6 (SAE C, 14 teeth)
- H1P 115/130 Auxiliary mounting - Option S1 (SAE B-B, 14 teeth)
- H1P 115/130 displacement limiter, option B and D
- Port Description H1P115/130
- Dimensions H1P 115/130
- Electric Displacement Control (EDC), option A2 (12 V) / A3 (24 V)
- H1P 115/130 Manual Displacement Control (MDC), option M1
- H1P 115/130 Manual Displacement Control (MDC) with NSS, option M2
- H1P 115/130 Manual Displacement Control (MDC) with CCO, option M3, M4
- H1P 115/130 Manual Displacement Control (MDC) with NSS and CCO, option M5, M6
- Non Feedback Proportional Electric control (NFPE), with manual override, option A8 (12 V) / B8 (24 V)
- Automotive Control (AC) Dimensions
- Forward-Neutral-Reverse (FNR) with manual override, options A9 (12 V) / B1 (24 V)
- H1P 115/130 suction filtration, option L
- H1P 115/130 filtration, option M
| 
Dimensions H1P 115/130Charge inlet port “S”Port ISO 11926-1 – 1 5/ 8 -12∅69.0 max. clearance dia for fittingCase drain port “L4”Port ISO 11926-1 – 1 5/ 16 -12∅63.0 max. clearance dia for fittingCase pressure portPort ISO 11926-1 – 1 1/ 16 -12∅41.0 max. clearance dia for fittingServo gauge port “M4”Port ISO 11926-1 – 7/16 -20∅24.5 max. clearance dia for fittingSystem port “B”∅31.5 – 450 barSplit flange bossper ISO 6162M12 x 1.7520 min.full thread depthSystem port “A”∅31.5 – 450 barSplit flange bossper ISO 6162M12 x 1.7520 min.full thread depthConnector :Deutsch DT04-2Pto be paint free12.45 ± 0.25[0.49 ± 0.01]46.4 ± 1.0[1.827 ± 0.039]141.5 ± 1.0[5.571 ± 0.039]167.4 ± 1.0[6.591 ± 0.039]67.0 ± 1.0[2.638 ± 0.039]162.4 ± 1.0[6.394 ± 0.039]77.2 ± 1.0[3.039 ± 0.039]178.4 ± 1.0[7.024 ± 0.039]151.5 ± 1.0[5.965 ± 0.039]132.0 ± 1.0[5.197 ± 0.039]4x 66.6 ± 0.25[2.622 ± 0.010]4x 31.8 ± 0.25[1.252 ± 0.010]8x 33.3 ± 0.25[1.311 ± 0.010]8x 15.9 ± 0.25[0.626 ± 0.010]8.05 ± 0.8[0.317 ± 0.031]17.9 ± 0.2[0.705 ± 0.008]65.0 ± 0.2[2.559 ± 0.008] 110.9 ± 0.2[4.366 ± 0.008] 106.5 ± 0.2[4.193 ± 0.008]316.846 ± 2.0[12.474 ± 0.079]R 0.8 max.[0.031]1.5 ± 0.5 x 45°±5°[0.059 ± 0.028 x 45°]∅152.4 + 0– 0.05[6.0 + 0– 0.002]80.0 + 0.1– 0.2[3.15 +0.004– 0.008 ]80.0 + 0.1– 0.2[3.15 +0.004– 0.008 ]239.415 + 0.6– 0.5[9.426 + 0.024– 0.02 ]Shaft LcShaft LcShaft LcP003 394EMounting flange surfaceFlange 152 - 4 per ISO 3019-1to be paint freeB-B (2x) D-DC-CZDDBBCCPlease contact Danfoss representative for specific installation drawings.Technical InformationH1P 115/130 Axial Piston Single PumpsInstallation drawings56 | © Danfoss | May 2018 BC00000198en-US0901 |
