Danfoss VLT AQUA Drive FC 202 Programming Manual

Also see for VLT AQUA Drive FC 202: Service guide Installation guide Installation guide Operating guide Installation guide

Contents

Danfoss VLT AQUA Drive FC 202 Programming Manual Manual pdf 203 page image

4.1.3 1-** Load/MotorPar.No. #Parameter description Default value 4-set-up FC 302onlyChangeduringoperationConver-sionindexType1-0* General Settings1-00 Configuration Mode ExpressionLimit All set-ups TRUE - Uint81-01 Motor Control Principle [1] VVC+ All set-ups FALSE - Uint81-03 Torque Characteristics [3] Auto Energy Optim. VT All set-ups TRUE - Uint81-06 Clockwise Direction [0] Normal All set-ups FALSE - Uint81-1* Motor Selection1-10 Motor Construction [0] Asynchron All set-ups FALSE - Uint81-1* VVC+ PM1-14 Damping Gain 120 % All set-ups TRUE 0 Int161-15 Low Speed Filter Time Const. ExpressionLimit All set-ups TRUE -2 Uint161-16 High Speed Filter Time Const. ExpressionLimit All set-ups TRUE -2 Uint161-17 Voltage filter time const. ExpressionLimit All set-ups TRUE -3 Uint161-2* Motor Data1-20 Motor Power [kW] ExpressionLimit All set-ups FALSE 1 Uint321-21 Motor Power [HP] ExpressionLimit All set-ups FALSE -2 Uint321-22 Motor Voltage ExpressionLimit All set-ups FALSE 0 Uint161-23 Motor Frequency ExpressionLimit All set-ups FALSE 0 Uint161-24 Motor Current ExpressionLimit All set-ups FALSE -2 Uint321-25 Motor Nominal Speed ExpressionLimit All set-ups FALSE 67 Uint161-26 Motor Cont. Rated Torque ExpressionLimit All set-ups FALSE -1 Uint321-28 Motor Rotation Check [0] Off All set-ups FALSE - Uint81-29 Automatic Motor Adaptation (AMA) [0] Off All set-ups FALSE - Uint81-3* Adv. Motor Data1-30 Stator Resistance (Rs) ExpressionLimit All set-ups FALSE -4 Uint321-31 Rotor Resistance (Rr) ExpressionLimit All set-ups FALSE -4 Uint321-33 Stator Leakage Reactance (X1) ExpressionLimit All set-ups FALSE -4 Uint321-34 Rotor Leakage Reactance (X2) ExpressionLimit All set-ups FALSE -4 Uint321-35 Main Reactance (Xh) ExpressionLimit All set-ups FALSE -4 Uint321-36 Iron Loss Resistance (Rfe) ExpressionLimit All set-ups FALSE -3 Uint321-37 d-axis Inductance (Ld) ExpressionLimit All set-ups FALSE -6 Int321-39 Motor Poles ExpressionLimit All set-ups FALSE 0 Uint81-40 Back EMF at 1000 RPM ExpressionLimit All set-ups FALSE 0 Uint161-46 Position Detection Gain 100 % All set-ups TRUE 0 Uint161-5* Load Indep. Setting1-50 Motor Magnetisation at Zero Speed 100 % All set-ups TRUE 0 Uint161-51 Min Speed Normal Magnetising [RPM] ExpressionLimit All set-ups TRUE 67 Uint161-52 Min Speed Normal Magnetising [Hz] ExpressionLimit All set-ups TRUE -1 Uint161-55 V/f Characteristic - V ExpressionLimit All set-ups TRUE -1 Uint161-56 V/f Characteristic - f ExpressionLimit All set-ups TRUE -1 Uint161-58 Flystart Test Pulses Current ExpressionLimit All set-ups FALSE 0 Uint161-59 Flystart Test Pulses Frequency ExpressionLimit All set-ups FALSE 0 Uint161-6* Load Depen. Setting1-60 Low Speed Load Compensation 100 % All set-ups TRUE 0 Int161-61 High Speed Load Compensation 100 % All set-ups TRUE 0 Int161-62 Slip Compensation 0 % All set-ups TRUE 0 Int161-63 Slip Compensation Time Constant ExpressionLimit All set-ups TRUE -2 Uint161-64 Resonance Damping 100 % All set-ups TRUE 0 Uint161-65 Resonance Damping Time Constant 5 ms All set-ups TRUE -3 Uint81-66 Min. Current at Low Speed ExpressionLimit All set-ups TRUE 0 Uint8Parameter Lists Programming GuideMG20O702 Danfoss A/S © Rev. 2014-01-21 All rights reserved. 2014 4