38Function Setup Function SetupENGLISHENGLISHIntroduction Connections Playback Function Setup OthersAfter you made IP address/DNS settings or when a LAN cable is connected, always perform theconnection test to check if the connection is correctly made.1) Press [SETUP] in stop mode.2) Use [Y / Z] to select , then press [ENTER].3) Use [Y / Z] to select , then press [ENTER].4) Use [U / V] to select “Network Connection”, then press [ENTER].5) Use [U / V] to select “Connection Test”, then press [ENTER].Connection test will start automatically and the test result will appear right after the connection testfinishes.• “Testing...” : The test is in progress.• “Pass” : Connection test is successfully completed.• “Fail” : Connection test failed. Check the connection settings.Press [ENTER] to go to the list of network status confirmation screen.6) Press [ENTER] to go back to the previous screen or press [SETUP] to exit.Network settings are set to the following settings initially. (In most cases, you can connect to theInternet without making any changes to the default settings.)If you want to set the network settings back to the default settings as above (except “BD-LiveSetting”), follow the procedure below.1) Follow steps 1) to 4) in “Connection Test” on this page.2) Use [U / V] to select “Enable(Easy)”, then press [ENTER].• The unit will start the connection test automatically and the test result will appear right after thetest finishes.• After the connection test finishes, press [ENTER] to go to network status confirmation screen.3) Press [ENTER] to activate the network settings and set the network connectionautomatically. Press [SETUP] to exit.If you need to set specific settings manually in accordance with your network environment, select“Enable(Custom)” to set each setting as necessary. IP Address Setting1) Follow steps 1) to 4) in “Connection Test” on this page.2) Use [U / V] to select “Enable(Custom)”, then press [ENTER].3) Use [U / V] to select “IP Address Setting”.4) Press [ENTER] repeatedly to select the desired setting.“Auto(DHCP)” : If your router has DHCP server function, select “Auto(DHCP)”.“Manual” : If your router does not have DHCP server function, select “Manual”.If you select “Manual”, follow the following instruction to set the IP address.Use [U / V] to select “IP Address”, then press [ENTER].• IP address setting screen will appear. Enter IP address, subnet mask and default gateway with[U / V / Y / Z] and [the Number buttons].• Enter the IP address number after checking the specifications of your router.• If the IP address number is unknown, check the IP address number of other devices.(e.g. PC connected via LAN cable) and assign a different number from those of other devices.After you enter all correctly, press [ENTER].• Confirmation message will appear.Network ConnectionConnection TestNote• If the connection test passes, you can enjoy the BD-Live functions using the Internet withoutmaking any extra settings.• If the connection test fails, you may need to change the MAC address settings of your router.You can check the MAC address of this unit at the bottom of the “Enable(Custom)” screen.Enable(Easy)- IP Address Setting Auto(DHCP)- DNS Setting Auto(DHCP)- Proxy Setting Do Not Use- Connection Speed Auto- BD-Live Setting AllowIP AddressSubnet MaskDefault GatewayPrimary DNSSecondary DNSthen press ‘ENTER’.Connection Test∗∗∗ . ∗∗∗ . ∗∗∗ . ∗∗∗∗∗∗ . ∗∗∗ . ∗∗∗ . ∗∗∗∗∗∗ . ∗∗∗ . ∗∗∗ . ∗∗∗∗∗∗ . ∗∗∗ . ∗∗∗ . ∗∗∗∗∗∗ . ∗∗∗ . ∗∗∗ . ∗∗∗Note• The setting of “BD-Live Setting” will not be set back to the default, even if you follow theprocedure.Enable(Custom)IP Address SettingIP AddressSubnet MaskDefault Gatewaythen press ‘ENTER’..........∗∗∗ ∗∗∗ ∗∗∗∗∗∗∗∗∗∗∗∗ ∗∗∗∗∗∗∗∗∗∗∗∗ ∗∗∗∗∗∗Remote control operationbuttons: Displaying the menuCancel the menu: Move the cursor(Up/Down/Left/Right) : Confirm the setting : Return to previous menu