Denon DCM-65/35 Operating Instructions Manual

Contents

15ENGLISHREMOTE CONTROL UNIT RC-258 Setting to the Program Mode• For program search, press the PROG/DIRECT button then the track numberbuttons (1 through 10 and +10).• The remote control unit is normally set to the direct mode.Drawer Open / Close Button(5 OPEN / CLOSE)Random Button (RANDOM)Repeat Button (REPEAT)Track Number Button (1 ~ 10)Play Button (1 PLAY)Pause Button (3 PAUSE)Stop Button (2 STOP)Automatic Search Forward Button (8)Automatic Search Reverse Button (9)Time Button (TIME)Program/Direct Button (PROG/DIRECT)Disc Select Button (DISC SELECT)Call Button (CALL)+10 Button (+10)Disc Skip + Button (DISC SKIP +)Disc Skip – Button (DISC SKIP –)Volume + buttons (VOLUME +)Volume – buttons (VOLUME –)Manual Search Forward Button (7)Manual Search Reverse Button (6)Use this to adjust the output level output of theVARIABLE.The volume increases when the (+) button is pressed,decreases when the (–) button is pressed.• Disc SelectionUse the DISC SELECT and number buttons to select the number of the discto be played.“–” appears on the disc number section of the display for 2 seconds whenthe DISC SELECT button is pressed. Press the number buttoncorresponding to the number of the disc to be played while “–” is displayedto select the disc number.Track numbers are selected if the number buttons are pressed while “–” isnot displayed on the disc number section of the display.• Direct SelectionNormally, direct search is possible simply by pressing the desired numberbuttons.• Program Selection (During playback, the track which is currentlyplaying is programmed as the 1st track.)Press the PROG/DIRECT button, then press the number buttons.For example, to program tracks number 3, 11, and 5, pressPROG/DIRECT / 3 / +10 and 1 / 5.To cancel the program, press the PROG/DIRECT button.• Inputting the Track NumbersFor track numbers below 10, simply press the corresponding button. Fortrack numbers of 11 and greater, press the +10 then the number buttons.For example, for track number 22 press +10 twice then 2.• VolumeThe volume control on the unit will operate when the volume buttons arepressed. The volume can be checked by looking at the position of thecontrol.• Skipping DiscsThe Disc Skip button (DISC SKIP +, –) will not function in the random and program modes.During disc sequential random playback, when the Disc Skip + button is pressed, the following disc is played in random order.• VolumeThe output level of the VARIABLE output terminal can be changed.When the volume button is pressed, “–” appears in the TIME M (minutes) section of the display window and the level appears in the S (seconds) section. Thevolume can be changed between a maximum of “00” and a minimum of “–12” in 12 steps, by approximately 1.5 dB per step.• The Time indicator indicates the amount of elapsed time for the track currently being played, the amount of time remaining for the current track and theamount of time remaining for all tracks yet to be played.Normally, the amount of elapsed time for the current track is displayed. Pressing this button once causes the indicator to light up, displaying theamount of time remaining for the current track. Pressing the button once more turns the indicator off and causes the indicator to light up, displayingthe number and the time remaining for all tracks yet to be played on the disc. Pressing the button once again turns the indicator off and causes theindicator to display the elapsed time for the current track.• During playback, the total remaining time is the remaining time for the disc. For programmed playback, the remaining time for the program is only displayedwhen the programmed tracks are all on the same disc.“– – – –” is displayed when tracks on more than one disc are programmed.• In the case that the total playing time of programmed tracks becomes more than 99:59, “– –: – –” is displayed.REMAIN–DISCREMAIN