Denon DN-A7100 User Manual

Also see for DN-A7100 - AV Surround Preamplifier: User guide Service manual

Denon DN-A7100 User Manual Manual pdf 24 page image

20ENGLISH1 INPUT SETUP (ASSIGNABLE DIGITALINPUT AND COMPONENT VIDEO INPUT)6 digital inputs, 3 component video inputs and 2HDMI inputs can be assigned to a desired source.Use this menu to select the digital input jack to beassigned to the input source.1. Select “INPUT SETUP” in SETUP MAINMENU with 3 or 4 cursor button, and press theENTER button.1-1 INPUT SETUPFUNC:MODE :DIG:HDMI:COMP------------------------TV :AUTO : 3 : - : -DVD :AUTO : 1 : 1 : 1VCR1:AUTO : - : - : 3DSS :AUTO : 2 : 2 : 2AUX1:AUTO : A : - : -MAIN NEXT EXIT1-2 INPUT SETUPFUNC:MODE :DIG:HDMI:COMP------------------------CD :AUTO : 4 : :TAPE:AUTO : - : :CD-R:AUTO : 5 : :AUX2:AUTO : - : :MAIN RETURN EXIT2. To select the input source and MODE, pressthe 3 or 4 cursor buttons.3. To select “DIG” “HDMI” or “COMP” for the inputjack, press the 1 or 2 cursor buttons.Select “DIG” for input sources, for automaticdetection of the digital input signal condition.If there is not a digital signal present, but thereis an analog signal present, the analog signalwill be played.Select “DIG”, when only a digital signal will beused. Select “ANA” for input sources for whichno digital input jacks are used.4. To select the vdieo source, select “HDMI” or“COMP” by pressing the 3 or 4 cursor buttons,and press the 1 or 2 cursor buttons to selectthe vdieo source to be assigned .5. After you complete this portion of the set up,move the cursor to MAIN with the 3 or 4 cursorbuttons and press the ENTER button.Notes:• When the TUNER is fixed to the analog input, youcan not select any digital input.• When a DTS-LD or DTS-CD is playing, this setup isnot available. This is to avoid noise being generatedfrom the analog input.• If “DIG” is selected and a DVD, compact disc orLD is fast-forwarded during playback, decodedsignals may produce a skipping sound. In such cases,change the setting to DIGITAL.2 SPEAKER SETUPAfter you have installed the DN-A7100, connected allthe components, and determined the speaker layout,it is now time to perform the settings in the SpeakerSetup menu for the optimum sound acoustics foryour environment and speaker layout.Before you perform the following settings, it isimportant that you first determine the followingcharacteristics:2-1 SPEAKERS SIZEWhen setting the speaker size in the SPEAKERSIZE sub-menu, use the guidelines given below.LARGE:The complete frequency range for the channel youare setting will be output from the speaker.SMALL:Frequencies of the channel you are setting lowerthan approx. 100 Hz will be output from thesubwoofer.If the Subwoofer is set to “NONE” and the frontspeakers are set to “LARGE,” then the sound willbe output from both the left and right speakers.2-1 SPEAKERS SIZESUBWOOFER : YESFRONT L/R : LARGECENTER : SMALLSURROUND L/R : SMALLSURR.BACK : 2CHSURR.BACK SIZE : SMALLLPF/HPF : 100HzBASS MIX : BOTHMAIN NEXT EXIT1. Select “SPEAKER SETUP” in SETUP MAINMENU with 3 or 4 cursor button, and press theENTER button.2. To select the each speaker, press the 3 or 4cursor buttons.3. To select the setting of each speaker size,press the 1 or 2 cursor buttons.4. After you complete this portion of the set up,move the cursor to “NEXT” with the 3 or 4cursor buttons and then press the ENTERbutton to go to the next page.SUBWOOFER:YES:Select when a subwoofer is connected.NONE:Select when a subwoofer is not connected.FRONT L/RLARGE:Select if the front speakers are large.SMALL:Select if the front speakers are small.• If “NONE” is selected for the Subwoofer setting,then this setting is fixed to “LARGE.”CENTERNONE:Select if no center speaker is connected.LARGE:Select if the center speaker is large.SMALL:Select if the center speaker is small.SURROUND L/RNONE:Select if no surround left and right speakers areconnected.LARGE:Select if the surround left and right speakers arelarge.SMALL:Select if the surround left and right speakers aresmall.SURR. BACKNONE:Select if no surround back left and right speakersare connected.2CH:Select if the surround back left and right speakersare connected.1CH:Select if the one surround back speaker isconnected.In this case, the audio signal is emitted form theSurround back L output terminal.Notes:If “NONE” is selected for the Surround L/R setting,then this setting is fixed to “NONE.”