Denon DN-A7100 User Manual

Also see for DN-A7100 - AV Surround Preamplifier: User guide Service manual

Denon DN-A7100 User Manual Manual pdf 36 page image

32ENGLISHAUX2 INPUTIf you don’t need to connect 7.1 Ch. input terminalswith multi channel decoder,L(front left) and R (front right) inputs terminals areavailable as AUX2 input.In this case, You can connect additional audio sourceto AUX2 as other audio input terminals.LIP.SYNCDepending on the image device (TV, monitor,projector, etc.) connected to the DN-A7100, a timelag can occur between image signal processing andaudio signal processing. Though minor, this timelag can interfere with movie and music enjoyment.The LIP.SYNC feature delays the audio signal withrespect to the image signal output from the DN-A7100 to correct the time lag between the soundand image. It can be operated with the “LIP.SYNC”and 1 and 2 cursor buttons of the remote controller.Set the remote controller to the AMP mode beforeoperating the LIP.SYNC feature. The initial setting isOFF (0 ms).The time lag can be adjusted in 10 mssteps up to 200 ms.Watch the picture on the image device (i.e., TV,monitor, projector, etc.) as you adjust the time lag.Note:The LIP.SYSNC feature turns OFF (0 ms) in thePURE DIRECT mode. When the PURE DIRECTmode is deactivated, the set value of the LIP.SYSNCfeature is automatically restored.BASIC OPERATION(TUNER)LISTENING TO THE TUNERFrequency scan step for AM is selectable.Default setup is 9 kHz step, if your country’s standardis 10 kHz step, Press BAND button on the remotemore than 6 seconds. Scan step will change.Note:Preset memory for the tuner will clear by changingthis setup.AUTO TUNING2.1.1. 2.(Using the DN-A7100)1. To select tuner and desired band (FM or AM),press the BAND button on the front panel.2. Press the 3 or 4 cursor buttons on the frontpanel for more than 1 second to start the autotuning function.3. Automatic searching begins then stops when astation is tuned in.(Using the remote control unit)1. To select tuner and desired band (FM or AM),press the BAND button on the remote.2. Press the TUNING – / + for more than 1 secondon the remote.3. Automatic searching begins then stops when astation is tuned in.If tuning does not stop at the desired station, use tothe “Manual tuning” operation.MANUAL TUNING2.1.1. 2.(Using the DN-A7100)1. To select tuner and desired band (FM or AM),press the BAND button on the front panel.2. Press the 3 or 4 cursor buttons on the frontpanel to select the desired station.(Using the remote control unit)1. To select tuner and desired band (FM or AM),press the BAND button on the remote.2. Press the TUNING – / + on the remote to tunein the desired station.DIRECT FREQUENCY CALL3.1.2.1. To select tuner and desired band (FM or AM),press the BAND button on the remote.2. Press the F.DIRECT on the remote, display willshow “FREQ - - - -”.3. Input your desired station’s frequency with thenumeric buttons on the remote.4. The desired station will automatically be tuned.1. Select a desired Video source to decide therouted video signal to the Monitor Outputs.2. Press 7.1 CH IN on the remote to switch the 7.1channel input.3. If it is necessary to adjust the output level ofeach channel, press the CH.SEL button on theremote.Adjust the speaker output levels so that you canhear the same sound level from each speakerat the listening position. For the front left, frontright, center, surround left, surround right andsurround back speakers, the output levels canbe adjusted between –10 to +10 dB.The subwoofer can be adjusted between –15and +10 dB.These adjustments result will be stored to 7.1CH. INPUT memory.4. Adjust the main volume with the VOLUMEknob or the VOL –/+ buttons on the remote.To cancel the 7.1 CH. INPUT setting, press 7.1 CHIN on the remote.Notes:• 7.1 CH. Input mode bypasses the internal surroundprocessing, so SURROUND mode cannot beselected.• In addition, there is no signal at the record outputswhen the 7.1 CH. Input is in use.