Denon DVD-3910 Operating Instructions Manual

Also see for DVD-3910: Supplementary guide Operating instructions Specifications Specification Service manual

19A simple 1-cable connection (using a commercially available cable) with a device having an HDMI (High-Definition Multimedia Interface)connector allows digital transfer of the digital images of DVD video and other sources, DVD video, and the multi-channel sound of DVDaudio.(9) HDMI connectionsDVD-3910HDMI InputconnectorHDMI cable(commercially available)Monitor equipped withHDMI input connectorsSetting of HDMIAudiorecordingformatDVDvideoMULTI(NORMAL) MULTI(LPCM)Dolby digital Dolby digital Multi PCMDTS DTS Multi PCMDVDAudioLPCM or PCCM(with CPPM) X XLPCM or PCCM(without CPPM) Multi PCM Multi PCMSuperAudioCDMulti area✽ The multi-channel/stereo area sound of Super Audio CD is notoutput.✽ The video and audio signals cannot be output when playingDVD AUDIO with CPPM.2CH2 channelPCM2 channelPCMX2 channelPCMConnection Examples for HDMI AUDIO SETUPHDMI-supported monitor or projector, etc. (2-channel support or no audio support)• 2CH ...............................Use this connection when you would like to enjoy the multi-channel audio output from an analog audio outputconnector, DENON LINK, or with the audio output from an IEEE 1394 connector.HDMI-supported monitor/AV amplifier, etc. (Supports DTS and Dolby Digital decoders)• MULTI (NORMAL).........Use this connection when you would like to enjoy the multi-channel audio output from an HDMI connector andyou wish to have a DTS, Dolby Digital, or other decoder connected to do the processing. (Speaker and othersettings are not required.)HDMI-supported monitor (Supports audio input for 2 or more channels)• MULTI (LPCM) ..............Use this connection when you would like to enjoy the multi-channel output from an HDMI connector and theconnection point does not support a DTS, Dolby Digital, or other decoder. (Speaker settings are permitted.)NOTES:• HDMI audio output settings permit the selection of either 2channels or multi-channels. When selectingMULTI(NORMAL) or MULTI(LPCM), a down-mixed audiosignal is output from the analog connectors (Left/Right andFront Left/Front Right) of the DVD-3910. To output multi-channel sound from the analog audio output connectors, setHDMI to OFF, or select “2CH”.• When select MULTI(NORMAL) or MULTI(LPCM), thesettings of “IEEE1394” and “DENON LINK” under “DIGITALINTERFACE SETUP” of “SETUP” cannot be made. Neithercan the settings of “AUDIO CHANNEL”, “DIGITAL OUT”,“LCPM(44.1kHz/48kHz)”, “SOURCE DIRECT”, or “BASSENHANCER” under “AUDIO SETUP”.The HDMI video and audio output are both turned off if thevideo output is set to “OFF” or if “ALL OFF” is set. (Seepages 47, 48.)Also note that it will not be possible to select the setting ofdigital output, when selecting “MULTI(NOMAL)” at “HDMIAUDIO SETUP”.• When selecting MULTI(NORMAL) or MULTI(LPCM), theDVD-3910 speaker settings under “AUDIO SETUP” becomeinvalid.• When playing a Super Audio CD with an HDMI connection,audio cannot be transferred beyond the CD layer. Make ananalog connection for this.• Among the devices that support HDMI, some devices cancontrol other devices via the HDMI connector; however, theDVD-3910 cannot be controlled by another device from theHDMI connector.• When using display equipment that is not supported by theHDCP (content protection function), the image will not beoutput properly. (See the compatibility table.)• The audio signals from the HDMI connector (including thesampling frequency and bit length) may be limited by theequipment that is connected.2 channelPCM2 channelPCM2 channelPCM2 channelPCM2 channelPCM2 channelPCM2 channelPCM2 channelPCMVideo CDCDMP3 CDWMA CD2 channelPCM2 channelPCM2 channelPCM2 channelPCMCD layerStereo areaX2 channelPCMXX2 channelPCMXX2 channelPCMXENGLISH