Desa Comfort Glow CGEFP33NR Owner's Operation And Installation Manual

Also see for Comfort Glow CGEFP33NR: OWNER'S OPERATION AND INSTALLATION MANUAL OWNER'S OPERATION AND INSTALLATION MANUAL OWNER'S OPERATION AND INSTALLATION MANUAL

Contents

21107569OWNER’S MANUALFor more information, visit www.desatech.comONOFFHILOMANUALIGNITIONCAUTION: Do not try to adjustheating levels by using the equip-ment shutoff valve.Figure 50 - Control LocationsContinued4. To lower flame, push HI/LO buttonon wall switch once.Note: This fireplace does not have apilot-only mode.AutomaticIgnitor ElectrodePilotBurnerFigure 49 - PilotONOFFHILOMANUALIGNITIONManual Ignition Bypass Switch(Up is for Remote Control)ON/OFFButtonHI/LOButtonWallSwitchOPERATINGFIREPLACEContinuedB. Using Hand-Held WirelessRemote Control1. Set manual ignition bypass switch oncontrol panel to OFF position (auto-matic ignition position).2. Wait five (5) minutes to clear out anygas. Smell for gas around heater andnear floor. If you smell gas, STOP!Follow “B” in the safety informationon warnings plate. If you don’t smellgas, go to the next step.TO TURN OFF GASTO APPLIANCEShutting Off Heater - WallSwitchPush ON/OFF button on wall switch once.Shutting Off Heater - WirelessRemote ControlPoint remote control toward lower frontof fireplace and push both buttons at thesame time.MANUAL LIGHTINGINSTRUCTIONSFOR ELECTRICALPOWER OUTAGEWARNING: You must operatethis heater with the fireplacescreen in place. Make sure fire-place screen is in place beforerunning heater.NOTICE: During initial operationof new heater, burning logs willgive off a paper-burning smell.Open damper or window to ventsmell. This will only last a fewhours.Because this fireplace has an electronicignition system, in the event there is a lossof power, it will be necessary to manuallylight the pilot with the piezo ignitor. Afterthe pilot is lit, the main burner will lightautomatically.1. Follow steps 1 through 3 under Nor-mal Lighting Instructions, page 20.2. Set manual ignition bypass switch oncontrol panel to ON position (manualignition position). See Figure 51.3. The pilot is attached to the rear ofthe front burner. You will be able tosee the pilot and spark electrodewithout removing the screen or logs.4. Place the magnetic manual overridehandle, provided with this unit, onthe end of the gas valve stem (see Fig-ure 51).3. Point remote control toward thelower front of fireplace and pushboth buttons at the same time. Holdfor 6 seconds. The gas valve will openand electronic ignition will beginsparking to light the pilot.Note: Youwill be able to hear a clicking soundduring this process. LED on wallswitch will light.Note: You may be running thisheater for the first time after connect-ing to gas supply or at the start ofyour heating season. If so, the ONbutton may need to be pressed again.This will allow air to bleed from gassystem. If several attempts to lightpilot fail, contact a qualified serviceperson or gas supplier for repairs.Until repairs are made, light and op-erate manually (see Manual LightingInstructions for Electrical Power Out-age, pages 20 and 21).4. When pilot flame is lit, the thermo-couple is heated by the flame. Whenthermocouple becomes hot (5 to 15seconds), main burner will automati-cally light on high flame.5. To lower flame, point remote controltoward lower front of fireplace andpush HI/LO button once.Note: This fireplace does not have apilot-only mode.Figure 51 - Control LocationsManual IgnitionBypass Switch(Down is ON)MagneticManual OverrideHandle ON/OFFButtonHI/LOButtonPiezoIgnitorWallSwitchGasValveManualIgnitorElectrodeLEDLED LED