Desa Comfort Glow LFP33PR Owner's Operation And Installation Manual

Contents

7104888OWNER’S MANUALINSTALLATIONContinuedNote: Your Comfort Glow fireplace isdesigned to be used in zero clearance instal-lations. Wall or framing material can beplaced directly against any exterior surfaceon the rear, sides, or top of your fireplace,except where standoff spacers are integrallyattached. If standoff spacers are attached toyour fireplace, these spacers can be placeddirectly against wall or framing materials.CAUTION: This fireplace cre-ates warm air currents. These cur-rents move heat to wall surfacesnext to fireplace. Installing fire-place next to vinyl or cloth wallcoverings or operating fireplacewhere impurities (such as to-bacco smoke, aromatic candles,cleaning fluids, oil or kerosenelamps, etc.) in the air exist, maydiscolor walls.WARNING: A qualified ser-vice person must install fireplace.Follow all local codes.WARNING: Never install thefireplace• in a bedroom or bathroom• in a recreational vehicle• where curtains, furniture,clothing, or other flammableobjects are less than 42 inchesfrom the front, top, or sides ofthe fireplace• in high traffic areas• in windy or drafty areasNOTICE: This heater is intendedfor use as supplemental heat.Use this heater along with yourprimary heating system. Do notinstall this heater as your pri-mary heat source. If you have acentral heating system, you mayrun system’s circulating blowerwhile using heater. This will helpcirculate the heat throughout thehouse. In the event of a poweroutage, you can use this heateras your primary heat source.Figure 5 - Assembling Brass TrimIMPORTANT: If you are recessing the fire-box in a wall, do not attach brass trim at thistime. See page 9.Note: The instructions below show assem-bling and attaching brass trim to fireplace.1. Remove packaging from three piecesof brass trim.2. Locate four brass screws, two adjust-ing plates with set screws, and twoshims in the hardware packet.3. Align shim under adjusting plate asshown in Figure 5.4. Slide one end of adjusting plate/shimin slot on mitered edge of top brass trim(see Figure 5).5. Slide other end of adjusting plate/shimin slot on mitered edge of side brasstrim (see Figure 5).ASSEMBLING ANDATTACHING OPTIONALBRASS TRIM(Included with MantelAccessory)Side BrassTrimTopBrassTrimSlotMitered EdgeSlotShimSet ScrewsAdjustingPlate6. While firmly holding edges of brasstrim together, tighten both set screwson the adjusting plate with slottedscrewdriver.7. Repeat steps 1 through 6 for other side.8. Tighten trim hanging screws (#10 x6.25 shoulder) into holes in cabinets.Place the assembled trim onto fireplacecabinet. Align hanging notches on trimwith hanging screws on side of fire-place (see Figure 6). Push trim firmlyinto place, sliding hanging notches overhanging screws.Use the dimensions shown for rough open-ings to create the easiest installation (seeBuilt-In Fireplace Installation, page 9).IMPORTANT: Vent-free heaters add mois-ture to the air. Although this is beneficial,installing fireplace in rooms without enoughventilation air may cause mildew to formfrom too much moisture. See Air for Com-bustion and Ventilation, pages 4 through 6.IMPORTANT: Make sure the fireplace islevel. If fireplace is not level, log set will notwork properly.CHECK GAS TYPEUse only propane/LP gas. If your gas supplyis not propane/LP gas, do not install fire-place. Call dealer where you bought fire-place for proper type fireplace.ELECTRICAL HOOKUP(Optional GA3750 BlowerAccessory )This fireplace accepts a blower assemblywith an electrical cord. The electrical cord isfive feet in length. You must locate fireplacewithin reach of a 120 volt grounded electricaloutlet. If not, you must install an electricaloutlet within reach of fireplace power cord.Figure 6 - Attaching Brass Trim toFireplaceTrimHangingScrewsAssembledBrass TrimHangingNotcheson Trim