Dynex DX-40L150A11 User Manual

Also see for DX-40L150A11: Firmware update Guía del usuario Quick setup guide Guía del usuario Guía De Instalación Rápida

Maintenance 29DX-40L150A11Remote controlGeneralNote: If the problem is not solved by using these troubleshootinginstructions, try turning off your TV, then turning it on again.Maintenance• Do not use your TV in areas that are too hot or too cold, becausethe cabinet may warp or the screen may malfunction. Your TVworks best in temperatures that are comfortable to you.• Storage temperatures are 32° to 122°F (0° to 50°C).• Working temperatures are 41° to 104°F (5° to 40°C).• Do not place your TV in direct sunlight or near a heat source.Cleaning• Clean your TV with a soft, lint-free cloth. If surfaces are extremelydirty, use a soft cloth dampened with a weak detergent solution.• Use an eyeglass cleaner to clean the screen. Never use alcohol,paint thinner, or benzine.• Before using a chemically treated cloth, read the instructions thatcame with the cloth.SpecificationsSpecifications subject to change without notice.Weight and dimensions shown are approximate.Problem SolutionRemote control does notwork.• Make sure that the power cord isplugged in.• Make sure that there are noobstructions between the remotecontrol and the remote controlsensor on the front of the TV.• Make sure that the batteries areinstalled correctly. For moreinformation, see “Installing remotecontrol batteries” on page 7.• Replace the batteries. For moreinformation, see “Installing remotecontrol batteries” on page 7.Trouble programming yourexisting universal remotecontrol.• See instructions and a table ofcommon codes in “Programming auniversal remote” on page 8.• Codes are subject to change. Forup-to-date codes, go towww.dynexproducts.com.• Replace the batteries. For moreinformation, see “Installing remotecontrol batteries” on page 7.• Refer to the User Guide thataccompanied your universal remotecontrol and contact themanufacturer if problems persistProblem SolutionOne or more channels donot display.• Make sure that the channels are notblocked. For more information, see“Setting parental control levels” onpage 22.• Make sure that the channels are nothidden. For more information, see“Hiding and adding channels” onpage 18.• The channel may have been deletedfrom the channel list. You can tuneto the channel by pressing thenumber buttons or you can add thechannel back to the channel list. Formore information, see “Changingchannel settings” on page 18.Password is lost. • Enter 9999 to access parentalcontrols, then set a new password.For more information, see “Settingparental controls” on page 20.Some settings cannot beaccessed.• If a setting is grayed, the setting isnot available in the current videoinput mode.TV cabinet creaks. • When the TV is in use, thetemperature rises naturally and maycause the cabinet to expand orcontract which can cause a creakingnoise. This is not a malfunction.Control buttons on the TVdo not work.• Disconnect the power cord, wait afew seconds, then reconnect thepower cord and turn on the TV.• Make sure that the Button Lockoption is set to Off. For moreinformation, see “Turning thebutton lock on or off” on page 21.Analog standard NTSCDigital standard ATSC, 8-VSB, Clear-QAMChannel coverage VHF: 2 - 13UHF: 14 - 69CATV: Mid band A-8 ~ A-1, A~lSuper band: J ~ WHyper band: AA ~ ZZ, AAA, BBBUltra band: 65 ~ 94, 100 ~ 135Power requirement AC 120 V ~ 60 HzPower consumption 210 W (with TV on)<1 W in standby modeAudio power 12 W + 12 W internal speakerS-Video input Y: 1 V (p-p), 75 ohm, negative syncC:0.286 V (p-p) (burst signal) 75 ohmVideo/audio input Video: 1 V (p-p), 75 ohm, negative syncAudio: 500 mV (rms)Component input Y: 1 V (p-p), 75 ohm, including syncPR/CR: ±0.35 V (p-p), 75 ohmPB/CB: ±0.35 V (p-p), 75 ohmAudio: 500 mV (rms)Suggested resolutions: 1080i, 720p,480p, 480iHDMI input 4 HDMI input jacksHDCP compliantE-EDID compliantSuggested scan rates: 1080p,1080i,720p, 480p, 480iVGA input E-EDID compliantSuggested scan rates: 640x480/60 Hz,800x600/60Hz, 1024x768/60Hz,1280x1024/60Hz, 1920x1080/60HzAudio input: Headphone mini-jack forstereo