Eaton All-Pro WPS2040M Instruction Manual

2Direct Mount:Using the 4 of the mounting screws provided(J), attachthe lighting system directly to a wall or ceiling usingthe attachment points located in the corners (Fig. 7). Ifanchors(K) are required, i.e. for drywall installation, use a3/16” drill bit to create pilot holes and set the anchors inplace with a hammer.D-Ring:Your lighting system can be hung or suspended by oneor both of the D-Rings. Simply rotate one or both ringsout from the housing, ensure the support method used issecurely fastened to the mounting surface, and place thesystem into position (Fig. 8).Bracket Mount:Attach the two included brackets (C) to a wall or ceilingusing the fasteners provided. Ensure the brackets areparallel and aligned with each other, positioned no morethan 9" apart (Fig. 9). Locate the grooves on the longsides of the fixture, rotating and snapping the fixture intothe brackets. Remove by pressing down on the tabs onthe brackets.Outdoor Installation:This system is designed to withstand rain and can beinstalled and used outdoors, however, the followingguidelines must be adhered to:• Only the solar panel port can be used when thesystem is exposed to moisture. The USB ports arenot designed for use in wet conditions.• All ports not in use must have the port coverssecurely in place at all times to prevent waterintrusion.• The ports (in a vertical orientation) or control side(in a horizontal orientation) of the system shouldalways be oriented downward to protect againstwater intrusion.• The system is designed to operate between 0° and104°F. To protect the Li-ion battery pack, the internalcharging circuitry will not allow the battery to chargebelow 32°F.Fig. 7Fig. 6Fig. 8Fig. 99"FUNCTIONSYour fixture has three operating modes which can by selected by pressing the power buttonrepeatedly: ON, AUTO and OFF. As you cycle through these modes the mode text will brieflyilluminate to confirm the mode selected.ON mode: this mode keeps the light on indefinitely, bypassing inputs from the motion sensoror photo sensor. Note that in ON mode the system will not shut down until you change modesor the battery is depleted.AUTO mode: this mode utilizes the integrated motion sensor and photo sensor, turning thelight on, at night or in the dark, only when motion is detected. The light will deactivate once nomotion has been detected for 3 minutes. The onboard motion sensor has a detection range of15’ with a detection zone of 360°.OFF mode: from AUTO mode, press the power button once more to shut the light off. Thecharging and discharging functions will continue to operate in OFF mode.Dimming: the system is equipped with an integrated dimmer that can be used in ON or AUTOmode. Turn the knob to the left to dim the light output and extend battery run time. Turn theknob to the right to increase output, which will shorten battery run time. See Table 1 belowfor fixture run time estimates.USB Output: the USB output produces 5V 2.1A, and is useful for charging and/or operatingmost smart devices and accessories requiring a USB input. Note that the integrated powersupply is a 8800mAh Li-ion battery pack, and any charging from the power supply will reducethe run time of the light fixture on a single charge.TABLE 1Approximate Run Times and Initial Lumens Based On Dimming Level:All figures assume the battery pack is fully chargedDimming Level Full Dimming Half Dimming No DimmingLight Output 10% 50% 100%Run Time 18 Hours 9 Hours 90 minutesInitial Lumen Output 200 1200 2400Wattage Equivalent 15W 75W 180W--B--MCCHARGINGThis system is capable of being charged with the included solar panel, or via micro USB.See Table 2 below for approximate charge times based on power source and input power.USB Charging:To charge the fixture using a mini USB charging cord (L), connect the mini USB side of thecord to the mini USB input on the fixture (Fig. 10). DO NOT use any USB power sourceexceeding 5V 2.1A power supply. Once an input charge is detected, the battery indicator willflash, indicating the battery level. Once the battery is fully charged, the indicator will remaina solid green.Solar Panel Charging:Connect the solar panel cord directly into the solar panelinput port on the fixture (Fig 10); use of the 17’ exten-sion cord (M) is optional. Please note that the batteryindicatory lights do not come on when charging with thesolar panel in order to conserve power and acceleratecharge time.TABLE 2.Typical Charge Times:Power Source USB USB Solar PanelInput Power 5V 2.1A 5V 1.0A Full Direct SunCharge Time 3.5 Hours 7 Hours 2-3 DaysTROUBLESHOOTINGLight does not comeon when in ON mode• Press the power button to cycle through the operating modes,verifying the level of charge using the battery level indicator.• Ensure the battery is fully charged, using the USB input ifpossible.• When using the solar panel, allow at least three (3) full sunnydays for the first charge or any time the battery pack becomescompletely depleted.Light does not comeon when in AUTOmode• The AUTO mode utilizes the integrated photo control and will notallow the light to come on when ambient light levels are too high.Ensure ambient light levels are low enough to activate the light.Test by completely covering the motion sensor with your hand orother opaque object.• Press the power button to cycle through the operating modes,verifying the level of charge using the battery level indicator.• Ensure the battery is fully charged, using the USB input ifpossible.• When using the solar panel, allow at least three (3) full sunnydays for the first charge or any time the battery pack becomesdepleted.Motion Sensor ismalfunctioning1. The motion sensor produces a detection zone extending 60°from center, or 120° total angle. Ensure the motion triggeringevent falls within the detection zone.2. The motion sensor utilizes PIR (passive infrared) technology,which detects movement and changes in relative heat. Extremeambient temperatures may reduce or inhibit motion detection.3. Relocate the fixture away from trees, moving cars, standingwater or other objects that may potentially cause interference.USB output is notworking• Verify battery level is full using battery level indicator lights bycycling the power button to the ON mode.• Verify the USB auxiliary device is compatible with 5V 2.1A input.• Ensure all connections on USB ports are secureBattery IndicatorLights do notcome on• Cycle power button to ON mode.• Battery indicator lights work when in ON mode and may not beon during AUTO mode when light is off.• If the main light is off and you are not charging or dischargingusing either USB port than the battery indicator light will not beon. This is intentional to conserve battery life.• Battery indicator lights do not come on during solar panelcharging and the main light is off. This is intentional to conservebattery life.Fig.10USB OutputUSB InputSolar panelinput