Eaton Halo WP1150LPC Instruction Manual

1Instruction Manual/Manuel d’instructions/InstruccionesQuestions?/ Des questions?/ ¿Preguntas? 1-800-334-6871 ConsumerProducts@eaton.comPACKAGING CONTENTS/CONTENU DE L’EMBALLAGE/CONTENIDO DEL PAQUETEITEMS REQUIRED(Purchase separately)• Phillips screwdriver• Flat head screwdriver• Weatherproof silicone caulkIMPORTANT SAFETY INSTRUCTIONSWhen using product, basic precautions should always be followed, including the following:• Heed all warnings, including below warnings AND those included on product.• Save these instructions and warnings.• For outdoor use only.• cULus LISTED for wet location.• Disassembling your fixture will void the warranty.• Your fixture is prewired and preassembled for easy installation.• Read and follow these instructions.• Risk of fire/electric shock. If not qualified, consult an electrician.• Disconnect power at fuse or circuit breaker before installing or servicing.CAUTION• Connect fixture to a 120 volt, 60 Hz power source. Any other connection voidsthe warranty.• Fixture should be installed by persons with experience in household wiring or by aqualified electrician. The electrical system, and the method of electrically connectingthe fixture to it, must be in accordance with the National Electrical Code and localbuilding codes.• Fixture designed for wall or eave mount to a junction box only. Mount fixture to agrounded, recessed-mounted standard junction box marked for use in wet locations.• Do not mount below 5 feet.• This device complies with Part 15 of the FCC Rules. Operation is subject to thefollowing two conditions: (1) This device may not cause harmful interference, and (2)this device must accept any interference received, including interference that may causeundesired operation.WARNING: FCC Regulations state that any unauthorized changes ormodifications to this equipment not expressly approved by the manufacturercould void the user’s authorization to operate this equipment.SAVE THESE INSTRUCTIONS.WP1150LPCWP1150LPCHWP1135LPCA. Fixture housingAlojamiento del portalámparasBoîtier de l’appareil d’éclairageENGLISH INSTALLING YOUR FIXTURE1. Turn power OFF at main breaker that runs to the junction box where fixture will be installed.2. Attach adjustable mounting bracket (C) to junction box on wall using two of the mountingplate screws provided (F). Either the #6 or #8 screws (F) provided will fit most standardjunction boxes. Position the bracket (C) so that the mounting studs (C) for the fixture arehorizontal. Tighten the rotation screws (C) on the bracket.3. Wire the fixture as described in “Wiring your fixture”.4. Remove Lens (B) by removing Lens screw (D), and tilting Lens away from the fixture at thebottom.5. Position the fixture so that the bracket screws pass through the backplate of the fixturehousing (A). Tighten the housing (A) to the mounting bracket (C) with the knobs (C)provided. Make sure your fixture is straight. Mounting bracket (C) does swivel so you canadjust to get fixture straight. Reinstall Lens (B) using Lens screw (D).6. Add silicone caulk around fixture to help maintain a weather resistant seal.7. Turn power back ON.WIRING YOUR FIXTURE1. Turn the power OFF at main fuse/breaker box.2. Connect the black fixture wire to the black supply wire (hot). Secure with a wire connector (E).3. Connect the white fixture wire to the white supply wire (neutral). Secure with a wireconnector (E).4. Connect the bare ground wire on the mounting bracket (C) to an appropriate supplyground or grounded junction box. Secure with a wire connector (E).NOTE: Be careful to connect the wires correctly. Make sure no bare strands of wire aresticking out of the wire connectors (E).MANUAL OPERATIONNOTE: You may choose to override the photo control.This will allow you to control the fixture from a wallswitch without the dusk-to-dawn feature.1. Snap the photo control cover (G) over the photocontrol on the face of the fixture (Fig. 1).C. Adjustable mounting bracket, knobs and screwsSoporte de montaje ajustable, perillas y tornillosSupport de montage réglable, boutons et visE (3) Wire connectors(3) Conectores de cable(3) Serre-filsF. (2) #6 and (2) #8 screws(2) Tornillos #6 y (2) tornillos #8(2) #6 et (2) vis #8G. Photo control cover (optional)Cubierta del control de foto celda (opcional)Couvercle de l’interrupteur photo-électrique(facultatif)B. Lens (installed on fixture)Lente (instalado en el artefacto)Lentille (installée sur l’appareil)D. Lens screw (installed in fixture)Tornillo del lente (instalado en el artefacto)Vis de lentille (installée dans l’appareil)Fig. 1GWARNING

/ 4

Related manuals for Eaton Halo WP1135LPC