Eaton Crouse-Hinds F892 Instruction Manual

12INM F892 Rev 1Part Numbers: Carriers Kits w/ F801 Kits w/ F802F822-CA F822-P*[-NR] F822-2-P*[-NR]F880-CA F880-P*[-NR] F880-2-P*[-NR]F880-CL F880-L*[-NR] F880-2-L*[-NR]F880-CR F880-R*[-NR] F880-2-R*[-NR]F882-CA F882-P*[-NR] F882-2-P*[-NR]F890-CA F890-P*[-NR] F890-2-P*[-NR]F892-CA F892-P*[-NR] F892-2-P*[-NR]WARNING:EXPLOSION HAZARD - DO NOT DISCONNECTEQUIPMENT UNLESS POWER HAS BEEN SWITCHEDOFF OR THE AREA IS KNOWN TO BE NON-HAZARDOUS.HAZARDOUS (CLASSIFIED) LOCATIONClass I, Division 2, Groups A, B, C, D, T4Class I, Zone 2, IIC T4-40C <= Tamb <= 65C-40C <= Tamb <= 50C (F802 total load > 60% of rated maximum)To be installed in an IP54 or better enclosureF8xx CARRIERF801orF802PluggedintoSocket APower Supplied to the Carrier must be fused for 8A circuitry.F801orF802PluggedintoSocket BDiagnostic ModuleSegment 1Segment 2Segment 3Segment 4Segment 5Segment 6Segment 7Segment 8+-s+-s+-s+-s+-s+-s+-s+-s+-s+-s+-s+-s+-s+-s+-sHost 1Host 2Host 3Host 4Host 5Host 6Host 7Host 8Power APower B GroundAlarm ContactCarrier May Contain a Single F801 or F802 module where redundancy is not needed ("-NR" option).In such cases, only one Power Supply connection is needed. Also for the Alarm Contactto work, an F800-BLK module must be installed in place of the missing F801 or F802 module.24VDC Power Suppliesmay be installed in theNon-hazardous area.Vmax = 24VDC (F801), 30VDC (F802)24VDCPowerSupply A24VDCPowerSupply A This is a Chassis Groundfor EMC Compliance andelectrical safety.This drawing is representative of the F8xx series of Carriers. There will be minor differences in the various models.Kits contain 1 or 2 F801 or F802 modules along with the Carrier and Pluggable Connectors.* = S for Pluggable Screw Terminal Connectors, C for Pluggable Cage Clamp Connectors.Each of the 8 Segments (Hostx, Segmentx) are isolated from one another and from the Power Supplies.Host Terminals connect to the Host Control system which may be in a non-hazardous area.+-s+-sDiag Seg connectors(not available on all carrier models)Imax(-NR) = 420mA (F801), 580mA (F802)Imax = 840mA (F801), 1.16A (F802)Do not mix an F801 and F802 on the same Carrier.Installation must be in accordance with the National Electrical Code (NFPA 70, Article 504),ANSI/ISA-RP12.6, or the Canadian Electrical Code (CSA C22.1), as applicable.Mike StrauserMike StrauserCONTROL DRAWING FOR F8xx CarriersCONTROL DRAWING FOR F8xx CarriersCLASS I, DIV 2 (ZONE 2)CLASS I, DIV 2 (ZONE 2)HAZARDOUS LOCATIONSHAZARDOUS LOCATIONS2221 Yew Street, Forest Grove, Oregon 97116 USADate: 2/10/10Date: 2/10/10Title:Approved By:Drawing Number: 502-087Drawing Number: 502-087 Rev.: D.0Rev.: D.0+-sA1A2GG+-+-+--+