Eaton HALO FT18VCW Instruction Manual

Questions?/Des questions?/¿Preguntas? 1-800-334-6871 ConsumerProducts@eaton.com1PACKAGING CONTENTS/CONTENU D E L ’ E M BALLAGE/CONTENIDO D E L P A Q U E TEInstruction Manual / Manuel d’instructions/ Instrucciones®• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different fromthat to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.WARNING: FCC Regulations state that any unauthorized changes ormodifications to this equipment not expressly approved by the manufacturercould void the user’s authorization to operate this equipment.SAVE THESE INSTRUCTIONS.FOR BEST RESULTS• Install light 10-25 feet above the ground basedon your model.• Do not mount fixture close to reflective surfacessuch as windows, white walls, white surfacesand water.• When installing two fixtures on one switch,make sure the switch is rated for at least a1 A inductive load.• When mounting fixture, make sure the photosensor orientation is at the top.• When mounting to a wall, make sure the fixtureis 7 in. on center away from eave and 13 incheson center away from inside corner of theexterior wall.MOUNTING AND WIRING YOUR FIXTUREWARNING: Risk of electric shock. Disconnectpower at fuse or circuit breaker before installingor servicing.NOTE: Fixture can be wall or eave mounted (Fig. 1).NOTE: Mounting Bracket (B) mounts to recessedmounted standard junction boxes (Fig. 2). Junctionbox must be at least 1-1/2 inch in depth for properinstallation for recessed mount application.1. Line up the slotted holes on the mounting bracket (B)with the holes on your junction box. Using either (2)#6 screws or (2) #8 screws (C) (depending on size ofthe holes in your junction box), attach the mountingbracket (B) to your junction box (Fig. 3).2. Connect house ground wire to mounting bracketground wire using the green screw provided (Fig. 3).3. Connect fixture black wire to house black wire, andfixture white wire to house white wire, using the wirenuts (E) provided (Fig. 4).ITEMS REQUIRED(Purchase separately)• Phillips screwdriver• Outdoor weatherproof silicone caulkingIMPORTANT SAFETY INSTRUCTIONSWhen using product, basic precautions should always be followed, including the following:• Heed all warnings, including below warnings AND those included on product.• Save these instructions and warnings.• For outdoor use only.• cULus LISTED for wet location.• Disassembling your fixture will void the warranty.• Your fixture is prewired and preassembled for easy installation.• Read and follow these instructions.• Risk of fire/electric shock. If not qualified, consult an electrician.• Disconnect power at fuse or circuit breaker before installing or servicing.CAUTION• Connect fixture to a 120 volt, 60 Hz power source. Any other connection voidsthe warranty.• Fixture should be installed by persons with experience in household wiring or by aqualified electrician. The electrical system, and the method of electrically connectingthe fixture to it, must be in accordance with the National Electrical Code and localbuilding codes.• Fixture designed for wall or eave mount to a junction box only. Mount fixture to agrounded, recessed-mounted standard junction box marked for use in wet locations.• Do not mount below 5 feet.FCC DECLARATION OF CONFORMITYThis device complies with part 15 of the FCC Rules. Operation is subject to the following 2conditions: (1) This device may not cause harmful interference, and (2) this device must acceptany interference received, including interference that may cause undesired operation.NOTE: This equipment has been tested and found to comply with the limits for a Class Bdigital device, pursuant to part 15 of the FCC Rules. These limits are designed to providereasonable protection against harmful interference in a residential installation. This equip-ment generates uses and can radiate radio frequency energy and, if not installed and used inaccordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. Ifthis equipment does cause harmful interference to radio or television reception, which can bedetermined by turning the equipment off an on, the user is encouraged to try to correct theinterference by one or more of the following measures:A. Light fixtureAppareil d’éclairageAccesorioENGLISHC. (2) #6-32 x 3/4 in. and (2) #8-32 x 3/4 in. junction box screws(use the size that fits your junction box)(2) vis nº 6 de 32 x 3/4 po et 2 vis nº 8 de 32 x 3/4 po pouboîtier de jonction (choisissez la dimension convenantà votre boîtier de jonction)(2) Tornillos #6-32 x 3/4 pulg. y (2) tornillos #8-32 x 3/4pulg. para montaje de la caja de conexiónes (utilice eltamaño que mejor se adecue a su caja de conexiónes)E. (2) Wire nuts(2) Serre-fils(2) Tuercas para cablesD. (2) Fixture Mounting Screws(2) Vis de montage(2) Tornillos de montaje del accesorioWARNINGB. Mounting bracketSupport de montageSoporte de montaje1AWall mountEave mount1B(White/Blanc/Blanco)FT28VCWFT28VCIWFT18VCWFT18VCIW(Bronze/Bronze/Bronce)FT28VCBFT28VCIBFT18VCBFT18VCIB3BJunction boxRound1-1/2 in.Octagonal1-1/2 in.2

/ 3

Related manuals for Eaton HALO FT18VCB