Eaton HALO MS276RD Instruction Manual

Eaton HALO MS276RD Instruction Manual Manual pdf 1 page image

Questions?/¿Preguntas? 1-800-334-6871 ConsumerProducts@eaton.com1PACKAGING CONTENTS/ C O N T E N I DO DEL P A Q U E T EInstruction Manual/InstruccionesITEMS REQUIRED(Purchase separately)• Phillips screwdriver• Outdoor weatherproof silicone caulking• (2) 150 watt (MAX) PAR 38 floodlight bulbsHOW IT WORKSPIR does a good job of detecting lateral motion across the 270°range of detection. Precision Plus Doppler Radar™ does anexcellent job detecting motion towards and away from the unit.Both systems combined provide enhanced accuracy and completecoverage within the detection range. Motion from any directionwill trigger your floodlight—even during hot or cold temperatureextremes.IMPORTANT SAFETY INSTRUCTIONSWhen using product, basic precautions should always be followed, including the following:• Heed all warnings, including below warnings AND those included on product.• Save these instructions and warnings.• For outdoor use only.• cULus LISTED for wet location.• Disassembly of your fixture will void the warranty.• Your fixture is prewired and preassembled for easy installation.• Read and follow these instructions.• To reduce the risk of shock during relamping, disconnect power supply to the unitbefore relamping.• Bulb gets HOT quickly!• The bulb and fixture get extremely hot during use. Disconnect power and allow fixtureto cool before changing bulb or handling fixture.• Always replace bulb with the same wattage or lower wattage than marked. Installinga bulb of a higher wattage could create a fire hazard. Use of a higher wattage bulbwill void the warranty. (Maximum 150 watt halogen bulb.)CAUTION• Connect fixture to a 120 volt, 60 Hz power source. Any other connection voidsthe warranty.• Fixture mounts to a recessed standard grounded junction box marked for use in wetlocations.Up to70 feet270 degrees• Fixture should be installed by persons with experience in household wiring or by aqualified electrician. The electrical system, and the method of electrically connectingthe fixture to it, must be in accordance with the National Electrical Code and localbuilding codes.• Do not allow sensor head to touch light housing – maintain at least 1 inch spacebetween fixture and sensor.• Keep away from flammable objects. Do not position fixture withintwo inches of any combustible materials.• MINIMUM 90°C SUPPLY CONDUCTORS.• For proper operation and protection against damage, the motion sensor headadjustment knobs must be facing the ground.• Do not use this apparatus near water.• Clean only with a dry cloth.• Do not block any ventilation openings. Install in accordance with the manufacturer’sinstructions.• Do not install near any heat sources such as radiators, heat registers, stoves or otherapparatus (including amplifiers) that produce heat.• Only use attachments/accessories specified by the manufacturer.• This device complies with Part 15 of the FCC Rules. Operation is subject to thefollowing two conditions: (1) This device may not cause harmful interference, and (2)this device must accept any interference received, including interference that may causeundesired operation. Under Part 15 of the FCC Rules, any changes or modifications tothe motion detector described in this instruction sheet that are not expressly approvedby Eaton could void the user’s authority to operate the equipment.NOTE: This equipment has been tested and found to comply with the limits fora Class B digital device, pursuant to Part 15 of the FCC Rules. These limits aredesigned to provide reasonable protection against harmful interference in aresidential installation. This equipment generates, uses and can radiate radiofrequency energy and if not installed and used in accordance with the instructions,may cause harmful interference to radio communications. However, there is noguarantee that interference will not occur in a particular installation. If this equipmentdoes cause harmful interference to radio or television reception, which can bedetermined by turning the equipment off and on, the user is encouraged to try tocorrect the interference by one or more of the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.- Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected.- Consult the dealer or an experienced radio/TV technician for help.WARNING: FCC Regulations state that any unauthorized changes ormodifications to this equipment not expressly approved by the manufacturercould void the user’s authorization to operate this equipment.SAVE THESE INSTRUCTIONS.MS276RD (Bronze)MS276RDW (White)A. Motion detector and light fixtureLuminaire avec détecteurde mouvementDetector de movimiento yartefacto de luzENGLISHD. Coverplate gasketJoint de couvercleJunta de la placade cubiertaC. (2) #6 and (2) #8 mounting screws(use the size that fits your junction box)(2) Vis nº 6 et (2 )vis nº 8 pour boîte de jonction(choisissez la dimension convenant à votreboîte de jonction)(2) Tornillos #6 y (2) tornillos #8 de montaje(utilice el tamaño que mejor se adecuea su caja de conexión)I. (2) Lampholder gaskets(2) Joints statiques de douille(2) Juntas obturadorasdel receptáculoE. (3) Wire nuts(3) Conectores del cables(3) Tuercas paraalambreB. Mounting bracketSupport de montageSoporte de montajeF. Mounting plate screwVis de la plaque demontageTornillo para la placade montajeG. Color-matchedcenter hole plugCouleur assortiebouchon de trou centralTapón para agujerocentral de colorcoincidenteH. (2) Light covers(2) Couvertures légères(2) Cubiertas de las lucesWARNINGQuestions?/Des questions?/¿Preguntas? 1-800-334-6871 ConsumerProducts@eaton.com