Eaton HALO MT125 Instruction Manual

Eaton HALO MT125 Instruction Manual Manual pdf 1 page image

Questions?/Des questions?/¿Preguntas? 1-800-334-6871 ConsumerProducts@eaton.com1Instruction Manual/Manuel d ’ instructions/InstruccionesPACKAGING CONTENTS/CONTENU DE L’EMBALLAGE/CONTENIDO DEL PAQUETEInstruction Manual / Manuel d’instructions/ InstruccionesITEMS REQUIRED(Purchase separately)• Phillips screwdriver• Drill with 3/16 in. drill bit (only needed if hole pattern on coverplate does not matchjunction box)• Weatherproof silicone caulking• (1) 150 watt (MAX) PAR 38 floodlight bulbNOTE: For improved energy efficiency, use lower wattage bulbs.IMPORTANT SAFETY INSTRUCTIONSWhen using product, basic precautions should always be followed, including the following:• Heed all warnings, including below warnings AND those included on product.• Save these instructions and warnings.• For outdoor use only.• cULus LISTED for wet location use.• Disassembling your fixture will void the warranty.• Your fixture is prewired and preassembled for easy installation.• Read and follow these instructions.• Risk of fire/electric shock. If not qualified, consult an electrician.• To reduce the risk of a burn during relamping, disconnect power supply to the unitbefore relamping.• The bulb and fixture get extremely hot during use. Allow fixture to cool completelybefore attempting to reposition fixture.• Disconnect power at fuse or circuit breaker before installing or servicing.• Disconnect power and allow fixture to cool before changing bulb or handling fixture.CAUTION• Connect fixture to a 120 volt, 60 Hz power source. Any other connection voidsthe warranty.• Fixture should be installed by persons with experience in household wiring or by aqualified electrician. The electrical system, and the method of electrically connectingthe fixture to it, must be in accordance with the National Electrical Code and localbuilding codes.• Mount fixture to a grounded junction box marked for use in wet locations.• Suitable for wall mount or eave mount only. NOT suitable for groundmount installation.• Keep away from flammable objects. Do not position fixture withintwo inches of any combustible materials.• Always use or replace bulb with the same wattage or lower wattage than required.Installing a bulb of a higher wattage could create a fire hazard and will voidthe warranty.• MINIMUM 90° C SUPPLY CONDUCTORS.• Fixture heads must be aimed in a downward direction. Aiming the fixture headsupward can result in accumulation of water in the fixture and will void the warranty.SAVE THESE INSTRUCTIONS.MOUNTING AND WIRING YOUR FIXTUREWARNING: Risk of electric shock. Disconnect power at fuse or circuit breaker beforeinstalling or servicing.NOTE: Junction box must be at least 1-1/2 inch indepth for proper installation (Fig. 1).1. The coverplate has been designed to work witha variety of different junction boxes (not included).Line up the holes in the coverplate with the screwholes in your junction box. If holes in the coverplatedo not match the screw holes on your junction box,drill holes in the coverplate using an 3/16 inch drillbit to match the screw holes on the junction box.3. Connect the black wire from the fixture to the black house supply wire and the white wirefrom the fixture to the white supply wire using wire nuts (D).4. Attach the ground wire coming from your house to the copper ground wire from thefixture (A) using wire nut (D). If no house ground wire is available, attach the copperground wire from the fixture to the junction box if it is metal and grounded. If junctionbox is not metal and no house ground wire is available, an alternative ground sourcemust be used for safe operation.5. Attach fixture to the junction box with two of the screws (C) provided. Either (2) #6 or (2)#8 screws will work with most standard junction boxes. Make sure that all screws aretightly secured.6. To prevent moisture from entering the junction box, apply a bead of silicone sealantaround the edge of the coverplate where it attaches to the junction box and anyopen holes.7. Insert lampholder gasket (B) into lampholder and screw bulb into lampholder.(Do not overtighten bulb.)8. Turn on power at main fuse/breaker box.AIMING THE LIGHTWARNING: Risk of electric shock. Disconnect power and allow fixture to cool beforechanging bulb or handling fixture.1. Loosen the knob on the side of the light housing (A) and locknut on arm.2. Tilt fixture head to desired position and then retighten.2-YEAR LIMITED WARRANTYTHE FOLLOWING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES,WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING, BUT NOT LIMITED TO, ANYWARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.Eaton warrants to customers that, for a period of two years from the date of purchase, Eaton’sproducts will be free from defects in materials and workmanship. The obligation of Eatonunder this warranty is expressly limited to the provision of replacement products. Thiswarranty is extended only to the original purchaser of the product. A purchaser’s receipt orENGLISHWARNINGMT125WMT125WH(White/Blanc/Blanco)A. Light fixtureLuminaireAccesorioRound1-1/2 in.Octagonal1-1/2 in.1B. (1) Lampholder gasket(1) Joint statique de douille(1) Junta obturadora del receptáculoC. (2) #6 and (2) #8 mounting screws(use the size that fits your junction box)(2) vis nº 6 et (2 )vis nº 8 pour boîte de jonction (choisissezla dimension convenant à votre boîte de jonction)(2) Tornillos #6 y (2) tornillos #8 de montaje (utilice eltamaño que mejor se adecue a su caja de conexión)D. (3) Wire nuts(3) capuchons de connexion(3) Conectores del cablesMT125MT125H(Bronze/Bronce)

/ 4

Related manuals for Eaton HALO MT125