Eaton HALO AL6501FL Instruction Manual

1Questions?/ Des questions?/ ¿Preguntas? 1-800-334-6871 ConsumerProducts@eaton.comInstruction Manual / Manuel d’instructions/ InstruccionesMOUNTING YOUR FIXTURENOTE: This fixture is intended to be conduit connectedto a properly installed and properly grounded metalweatherproof junction box (not included). All conduitconnectors, conduit, and junction boxes (sold separately)should be UL Listed suitable for wet locations.1. Using the pattern on the box, mark and drill holesfor mounting.NOTE: Mount this fixture in an upright position.2. Install the two bottom mounting screws (E) first,leaving enough room between the mountingscrews and the mounting surface to accommodatemounting the fixture.3. Screw the top mounting screw (E) into the predrilledhole and back the screw out. This will leave the holethreaded and make installation of the fixture easier.4. Remove access cover (D) from parts bag.5. Install the first conduit connector and conduit(sold separately) into the access cover (D).6. Feed supply wires into conduit and make wiringconnections as described in “Wiring Your Fixture”.7. Attach access cover (D) to the light fixture (A)using the two access cover mounting screws (F)provided (Fig. 1).NOTE: Make sure all wiring is placed into the armprior to tightening the access cover screws (F).8. Using the three mounting screws (E) provided, boltthe housing (A) to the mounting surface.9. Connect second conduit and conduit connector atthe junction box (Fig. 2).10. Fasten lens assembly (B) to housing (A) using thetwo lens assembly lock screws (G) and two washers(H) provided (Fig. 3).NOTE: Washers must be used to keep the lens in place.WIRING YOUR FIXTURE1. Turn off the power at the main fuse/breaker box.2. Attach ground wire that is attached to fixturehousing (A) to the junction box earth ground wire.3. Connect the black fixture wire to the black supply wire (hot). Attach UL approved wireconnector (sold separately).4. Connect the white fixture wire to the white supply wire (neutral). Attach UL approved wireconnector (sold separately).NOTE: Be careful to connect the wires correctly. Make sure no bare strands of wire extendfrom the wire nut or other approved wire connectors (sold separately).PACKAGING CONTENTS /CONTENU DE L’EMBALLAGE/CONTENIDO DEL PAQUETEITEMS REQUIRED(Purchase separately)• Phillips screwdriver• Adjustable wrench• Drill with 3/16 in. drill bit• 1/2 in. diameter flexible conduit (if applicable, length depends on application)• 1/2 in. watertight conduit connectors (if applicable)• Wire connectorsIMPORTANT SAFETY INSTRUCTIONSWhen using product, basic precautions should always be followed, including the following:• Read and follow these instructions.• Heed all warnings, including below warnings AND those included on product.• Save these instructions and warnings.• For outdoor use only.• cULus LISTED for wet location use.• Disconnect at fuse or circuit breaker before installing or servicing.• Disconnect power and allow fixture to cool before changing bulb or handling fixture.• Edges may cut. Handle with care.Notice: Lamps contain mercury, dispose according to local, state, or federal laws.For more information, visit: www.lamprecycle.org.CAUTION• Connect fixture to a 120 volt, 60 Hz power source. Any other connection voidsthe warranty.• Fixture should be installed by persons with experience in household wiring or by aqualified electrician. The electrical system, and the method of electrically connectingthe fixture to it, must be in accordance with the National Electrical Code and localbuilding codes.• Always use same wattage and type of bulb that was included with the fixture. Failureto do so will void the warranty. See fixture for wattage.• Upside down installation can result in overheating or accumulation of water in fixture.Install right side up.• MINIMUM 90° C SUPPLY CONDUCTORS.• This device complies with Part 18 of the FCC Rules.• This product may cause interference to radio equipment and should not be installednear maritime safety communications equipment, ships at sea or other criticalnavigation or communications equipment operating between 0.45-30 MHz.AL6501FLAL6501FLHA. Fixture housing withlight sensorBoîtier du luminaire avecdétecteur de lumièreAlojamiento del accesoriocon detector de luzENGLISHE. (3) Mounting screws(3) Vis de montage(3) Tornillos de montajeB. One-piece lensassemblyEnsemble de lentilled’une seule pièceEnsamblado dellente de una sola piezaC. 65 watt fluorescent bulbAmpoule fluorescente de65 wattsBombilla fluorescentede 65 vatiosD. Access coverCache d’accèsCubierta deaccesoG. (2) Lens assembly lock screws(2) Vis de blocage pour assemblage lentille(2) Tornillos de fijación delensamblado del lenteF. (2) Access cover mounting screws(attached to fixture)(2) Vis de montage du cache d’accès(attached to fixture)(2) Tornillos de la cubierta de acceso(conectado al accesorio)H. (2) Washers(2) Arandelas(2) RondellesFig. 2ConduitJunctionboxConduitconnectorAFig. 1FFDAFig. 3ABGHWARNING

/ 5

Related manuals for Eaton HALO AL6501FL