UPS OPERATING INSTRUCTIONSEATON Eaton 9395 550/275 UPS (225–550 kVA) Installation and Operation Manual 164201716 Rev 2 www.eaton.com/powerquality7-8Table 7‐3. Display Menu Operation (continued)OperationSubfunctionFunctionHigh Alert Timer The High Alert Timer screen sets the length of time the all UPMs remain active beforetransferring back to Variable Module Management System mode. The time can be set in 10minute increments from 0 to 990 minutes. Select HIGH ALERT TIMER from the ModuleManagement System Setup screen to display the High Alert Timer screen. Use the up or downarrow pushbutton to set the time. Press SAVE or ABORT. Once the action is completed, theModule Management System Setup screen is displayed.System Level 1 Setup Password The System Setup Level 1 screen can be used to set the UPS date and time, set the serial ports,change the Level 1 password, and log out of Level 1. In addition, the Level 0 functions areavailable. A password is required to access the Level 1 functions. To enter the password, selectENTER PASSWORD from the System Setup Level 0 menu to display the Enter Password screen.Use the left or right arrow pushbutton to select the password character position. Use the up ordown arrow pushbutton to change the password character. Once the password is entered,press the DONE pushbutton. The System Setup Level 1 menu screen is displayed. The defaultpassword is L1.Function Selection Use the up or down arrow pushbutton to highlight the setup function screen desired, then pressthe SELECT pushbutton to display the function screen. The Level 1 screen times out after60 minutes or can be logged out at any time by selecting the LOG OUT function from the menuscreen.Change Password The Change Password screen allows the System Setup Level 1 password to be changed. SelectCHANGE PASSWORD from the System Setup Level 1 menu to display the Change Passwordscreen. Use the left or right arrow pushbutton to select the password character position. Usethe up or down arrow pushbutton to change the password character. Once the new password isentered, press the DONE pushbutton. The Change Password Save screen is displayed.Change Password Save The Change Password Save screen lets you save the new password, retry another password, orabort the password change. Press SAVE, RETRY, or ABORT. If SAVE or ABORT is pressed, theaction is completed, and the System Setup screen displays. If RETRY is pressed, the ChangePassword screen is redisplayed.Time Format The Time Format Setup screen allows the selection of either month/day/year or day/month/yearformats for display on the screen and for logging events in the Event and History Logs. SelectSET DATE AND TIME from the System Setup Level 1 menu to display the Time Format Setupscreen. Use the up or down arrow pushbutton to highlight the desired format, then press theSELECT pushbutton to display the Set Date and Time screen. To return to the System Setupscreen, press the ESC pushbutton.Set Date and TimeMM/DD/YYYYThe Set Date and Time MM/DD/YYYY screen allows the internal date and time of the UPS to beset in the month/day/year format. The date and time information is used for display on thescreen and for logging events in the Event and History Logs. Use the left or right arrowpushbutton to highlight the setting to be changed. Use the up or down arrow pushbutton to makethe change. When finished making changes, use the left or right arrow pushbutton to highlightSAVE and the up or down arrow pushbutton to select YES. To complete the save function andreturn to the System Setup screen, select the return arrow pushbutton.Set Date and TimeDD/MM/YYYYThe Set Date and Time DD/MM/YYYY screen allows the internal date and time of the UPS to beset in the day/month/year format. The date and time information is used for display on thescreen and for logging events in the Event and History Logs. Use the left or right arrowpushbutton to highlight the setting to be changed. Use the up or down arrow pushbutton to makethe change. When finished making changes, use the left or right arrow pushbutton to highlightSAVE and the up or down arrow pushbutton to select YES. To complete the save function andreturn to the System Setup screen, select the return arrow pushbutton.Com Port Selection The Com Port Setup screen allows selection of the serial COM port to set up. Select COM PORTSETUP from the System Setup Level 1 menu to display the COM Port Setup screen. Use the upor down arrow pushbutton to highlight the COM port to be set up, then press the SELECTpushbutton. To return to the System Setup screen, press the ESC pushbutton.
