Eaton Solstar Instruction Leaflet
Safe Operation1. Check the rating label for voltage and frequency before connecting this luminaire to the electrical supply.2. Ensure that the mains supply is switched off when working on this luminaire, whether installing, re- lampingor carrying out any other servicing.3. Use the correct lamps as initially supplied or as indicated on the ballast label.4. This luminaire is suitable for mounting in direct contact with non-combustible materials, e.g. Metal,concrete, plaster. It is also suitable for mounting adjacent to normally flammable materials, e.g. Timber,chipboard, providing the top surface is spaced not less than 25mm from such materials. Do not mountluminaire on or close to readily flammable materials.5. To prevent damage to H.F. Ballasts do not mix H.F. And conventional magnetic Ballasts on the sameelectrical circuit.6. Where use in more onerous situations is required, e.g. In part-completed buildings before “drying-out” iscompleted, or areas where ambient temperatures are outside the normal temperature range, then consultour Sales Office.Servicing and Disposal1. At commissioning and handing over of installation ensure that a copy of these instructions is presented tothe authority responsible for the operation and maintenance of the luminaries.2. Servicing, e.g. cleaning, lamp replacement, must only be carried out after the electricity supply has beenswitched off. It must not be assumed that luminaries with lamps not lit are switched off always check beforeservicing.3. Cleaning should be carried out at regular intervals to ensure that dirt does not accumulate to an extent thatwill impair the thermal safety or optical performanceof the luminaire. Regular cleaning will also ensure thatthe optical performance of the luminaries is maintained.4. Failed lamps and starter switches must be replaced as soon as practicable by lamps and starters of thesame type. For electronic start circuits allow one minute for the thermal cut out to re-set beforeswitching on the mains supply.5. At the end of life the lamp and luminaire are classed as WEEE under directive 2002/96/EC and should bedisposed of in accordance with local legislation.Additional Instructions for Emergency versions1. Ensure mains supply is turned OFF.Connect mains supply cable to the 4-way plug supplied. (as shown opposite)2. Knock out one of the 6.5mm dia knockout features in the geartraycover with a gentle tap from a hammer, using a Philips screwdriver.3. Refer to standard installation instructions 1 and 2.Fit the LED into the mounting hole in the bezel using theretaining clip provided. (Unless using Solstar attachment,in which case see the Solstar attachments leaflet for LED position).4. Refer to standard instructions 3 and 4.Solstar with Digital DimmingPlease refer to 'Digital Regulating Luminaires' leaflet for further information.Connect mains/controls cable to the 6-way plug supplied.(as shown opposite) Note that both standard and emergencyluminaires have 6 pole mains/control connectors.GearboxFixing ClipsReflectorThumb wheelMain casingLamps(Quantity dependenton fitting)Note:For attachments,bezel fixingsmay need fittingprior to installationD2Switched LiveEarthNeutralUnswitched Live/SpareD1D2N12Switched LiveEarthNeutralUnswitched LiveN12D1IP65 Product luminaires comply with EN60598-1 and are suitable for use in normal interior conditions.o o This luminaire has an ambient temperature range of 5 C to 25 CInstruction Leaflet K1011V2 April 2016Instruction Manual - K1011V2April 2016Solstar (Horizontal)K1011V2EatonWheatley Hall Road, Doncaster, South Yorkshire, DN2 4NBSalesT: +44 (0)1302 303303F: +44 (0)1302 367155E: sales@cooper-ls.comGeneral+44 (0)1302 321541+44 (0)1302 303220technical@cooper-ls.comInternational Sales+44 (0)1302 303250+44 (0)1302 303251export@cooper-ls.comSolstar (Horizontal)with plug connectorIP44IP20 |
Related manuals for Eaton Solstar
Eaton K1121V3 Instruction Leaflet
Eaton K1121V10 Instruction Leaflet
Eaton SL4-SWD Series Instruction Leaflet
Eaton SL7-AP Series Instruction Leaflet
Eaton SL7-ASI Series Instruction Leaflet
Eaton RMQ-Titan M22-XLED Series Instruction Leaflet
Eaton L-852G Instruction Manual
Eaton RL56 Instructions Manual
Eaton Sure-Lites SELIN Series Installation Instruction
Eaton ALL-PRO Instruction Manual
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine