GE F60 Instruction Manual

Also see for F60: Communications manual Communications guide Instruction manual Instruction manual Instruction manual

Contents

CHAPTER 5: SETTINGS PRODUCT SETUPF60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-1155PUSHBTN 1 HOLD — This setting specifies the time required for a pushbutton to be pressed before it is deemed active. Thistimer is reset upon release of the pushbutton. Note that any pushbutton operation requires the pushbutton to be pressed aminimum of 50 ms. This minimum time is required prior to activating the pushbutton hold timer.PUSHBTN 1 SET — This setting assigns the FlexLogic operand serving to operate the pushbutton element and to assertPUSHBUTTON 1 ON operand. The duration of the incoming set signal must be at least 100 ms.PUSHBTN 1 RESET — This setting assigns the FlexLogic operand serving to reset pushbutton element and to assertPUSHBUTTON 1 OFF operand. This setting is applicable only if pushbutton is in latched mode. The duration of the incoming resetsignal must be at least 50 ms.PUSHBTN 1 AUTORST — This setting enables the user-programmable pushbutton autoreset feature. This setting is applicableonly if the pushbutton is in the “Latched” mode.PUSHBTN 1 AUTORST DELAY — This setting specifies the time delay for automatic reset of the pushbutton when in thelatched mode.PUSHBTN 1 REMOTE — This setting assigns the FlexLogic operand serving to inhibit pushbutton operation from the operandassigned to the PUSHBTN 1 SET or PUSHBTN 1 RESET settings.PUSHBTN 1 LOCAL — This setting assigns the FlexLogic operand serving to inhibit pushbutton operation from the front panelpushbuttons. This locking functionality is not applicable to pushbutton autoreset.PUSHBTN 1 DROP-OUT TIME — This setting applies only to “Self-Reset” mode and specifies the duration of the pushbuttonactive status after the pushbutton has been released. When activated remotely, this setting specifies the entire activationtime of the pushbutton status; the length of time the operand remains on has no effect on the pulse duration. This settingis required to set the duration of the pushbutton operating pulse.PUSHBTN 1 LED CTL — This setting assigns the FlexLogic operand serving to drive pushbutton LED. If this setting is “Off,” thenLED operation is directly linked to the PUSHBUTTON 1 ON operand.PUSHBTN 1 MESSAGE — If pushbutton message is set to “High Priority,” the message programmed in the PUSHBTN 1 ID andPUSHBTN 1 ON TEXT settings are displayed undisturbed as long as PUSHBUTTON 1 ON operand is asserted. The high priorityoption is not applicable to the PUSHBTN 1 OFF TEXT setting.This message can be temporary removed if any front panel keypad button is pressed. However, 10 seconds of keypadinactivity restores the message if the PUSHBUTTON 1 ON operand is still active.If the PUSHBTN 1 MESSAGE is set to “Normal,” the message programmed in the PUSHBTN 1 ID and PUSHBTN 1 ON TEXT settingsare displayed as long as PUSHBUTTON 1 ON operand is asserted, but not longer than time period specified by FLASH MESSAGETIME setting. After the flash time is expired, the default message or other active target message is displayed. Theinstantaneous reset of the flash message is executed if any relay front panel button is pressed or any new target ormessage becomes active.The PUSHBTN 1 OFF TEXT setting is linked to PUSHBUTTON 1 OFF operand and displays in conjunction with PUSHBTN 1 ID only ifpushbutton element is in the “Latched” mode. The PUSHBTN 1 OFF TEXT message displays as “Normal” if the PUSHBTN 1MESSAGE setting is “High Priority” or “Normal.”PUSHBUTTON 1 EVENTS — If this setting is enabled, each pushbutton state change is logged as an event into the eventrecorder.The figures show the user-programmable pushbutton logic.